Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EDS ES Series
Summary of Contents for EDS ES Series
- Page 1 ES Series WARNING SYSTEMS VOICE ANNOUNCEMENT Installation Manual www.eds.com.tr...
-
Page 2: Product Family
DESCRIPTION It is designed to provide point emergency announcements for visually-impaired people. The system consists of an audible and flashing announcement module and a wireless alert button. The storage for sound recording have been divided into four sections each of them is 20 seconds long, 80 seconds in total. Four different scenarios could be chosen for recording messages (evacuation, routing to another area, regional fire risk, forbidden zone). - Page 3 PHYSICAL ES12 / ES24 Audio Alert Device EKB Wireless Alert Button...
-
Page 4: Specifications
SPECIFICATIONS Model ES12 ES24 Environment class IV Outdoor Electrical Operating voltage 160-265V AC Input voltage 12V DC 24V DC Flasher White Speaker/Speaker Protection 8ohm/Available Sound power/Sound power level 20W/Adjustable 75W/Adjustable Harmonic distortion <%0,1 Amplifier efficiency >%93 Watchdog protection Available Detector connection ECP2L Optical Smoke Detector Fire alarm button connection ECB20R Fire Button... -
Page 5: Battery Unit
Battery unit Battery 12V/1.2Ah 2 x 12V/1.2Ah Battery charging time Max. 72 hours, full charge capacity Fixed discharge time is higher than nominal capacity. 24 hour charge Nominal ampere hour >%80 Battery charging current It must be charged at a current > c/10. Corrosion fault Alert information is available on the device (max 4 hours). - Page 6 The year and week of manufacture is included in the first four digit of your product serial number (located on the product identification label) Manufacturer EDS Elektronik Destek Sanayi ve Ticaret Ltd. Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785 Sancaktepe / Istanbul / TURKEY Recycle...
- Page 7 CONNECTIONS Audio Alert Device Figure 1: Front Panel LED 1 Green Power LED LED 2 Green (BATTERY) Permanent: Supplying from battery. Flashing. Battery s being charged. LED 3 Red (ALARM) Alarm existing in wired or wireless zone. LED 4 Orange (ZONE ERROR) Permanent: Zone open circuit.
- Page 8 LED card mounting; The connector is fixed to socket input on the lower part of the card as shown in Figure 2. The screw holes on LED card are placed corresponding to screw holes on the part with number (1) as shown in the picture and they are screwed down with 3x6 metric screws.
- Page 9 Record 3: The announcement of “Emergency Exit is Here” in case of giving alarm from wireless button. Record 4: Reserved for wireless contact. It will include announcement regarding unnecessary disuse of emergency exits. Record 1 is privileged from other announcements. While other announcements are made and if the condition develops stated for record 1, then other announcements are silenced and the record 1 announcement is started.
- Page 10 The jumper bookmarked with (8) should be normally in installed state. When this jumper is removed, record begins and red LED flashes. When the record is when the record is completed, LED goes out and the recorded sound is announced. (Figure:3) The jumper bookmarked with (8) is installed to its place and the reset button is pressed.
- Page 11 Terminal block (11) is used to connect the wired smoke detector and wired manual call point. 4K7 valued terminating resistor should be connected to end of line in order not to give open circuit fault. Figure 8: Zone terminal RESET Silencing of the Announcement After the announcement causing trigger (button, trigger entry) is returned to its normal condition, the announcement is silenced by pressing the reset...
- Page 12 ADDITIONAL MODULE ATTACHMENT Wireless Fire Button Attachment Remove the wireless devices to be attached from their boxes, and before installing the cells, remove the J1 jumper on the panel and wait till the red LED lights (30 seconds). At this stage, the lighting of the LED states that the learning mode is passed.
Need help?
Do you have a question about the ES Series and is the answer not in the manual?
Questions and answers