Page 1
User Manual PA70W 40 Watt Power Amplifier All Rights Reserved Version: PA70W/100V_2014V1.3...
Page 2
40W Power Amplifier Safety Operation Guide In order to guarantee the reliable operation of the equipments and safety of the staff, please abide by the following proceeding in installation, using and maintenance: 1) The system must be earthed properly. Please do not use two blades plugs and ensure the alternating power supply ranged from 100v to 240v and from 50Hz to 60Hz.
Page 3
40W Power Amplifier NOTICE: Please read this user manual carefully before using this product. Pictures shown in this manual is for reference only, different model and specifications are subject to real product. This manual is only for operation instruction only, not for any maintenance usage. The functions described in this version are updated till October 2014.
40W Power Amplifier 1. Introduction 1.1 Introduction to 40 Watt Power Amplifier 40 Watt Power Amplifier is a 40 Watt power amplifier (Class-D) with output alternatively at 70V or 100V. It has 2 stereo inputs (1x3.5mm jack for line in, 2xRCA for L&R), 1 digital input &...
40W Power Amplifier 1 x Power Cord 4 x Plastic Cushions 1 x User manual Note: Ensure the product and the accessories are all included, if not, please contact with the dealers. 2. Panel Description 2.1 Front Panel Figure 1 Front Panel Name Function To select the input audio source, after choosing the audio...
40W Power Amplifier 2.2 Introduction of Rear Panel Figure 2 Rear Panel Name Function Power Turns red when power on. ① Indicator 3-pole captive screw connector for microphone input, the dial Microphon switch in right side is to select the micro input kind, including ②...
40W Power Amplifier 3. System Connection 3.1 Usage Precautions 1) No working with empty load is allowed. 2) Speakers must be connected before power on. 3.2 System Diagram IR Receiver IR Remote Speaker (100V/10W) Speaker (100V/10W) Speaker Speaker (100V/10W) (100V/10W) PC 1 Blu-ray Figure 3 System Diagram...
40W Power Amplifier COM 70V 100V Speaker Speaker Speaker Speaker (100V/10W) (100V/10W) (100V/10W) (100V/10W) Figure 4 Audio Output Connection Note: Speakers to be connected should be with constant pressure. 3.3.2 Audio Inputs 40 Watt Power Amplifier provides with 2 stereo audio inputs, one microphone input and one digital fiber audio input.
40W Power Amplifier “-” and “ ” connect to ground, and “+” connects to signal. b) Balanced connection: “+” connects to positive, “-” connects to negative and “ ” connects to ground. LINE input When the switch turns to “LINE” (It has a low frequency characteristics, and wide frequency response in this mode), the microphone input is used for connecting with normal audio or wireless microphone output.
40W Power Amplifier 4.1.2 Volume/EQ controlling The line volume and MIC volume can be controlled by the buttons. The MIC Volume/LINE volume/LINE bass/LINE treble will be selected by the buttons, and controlled up/down/mute by the function buttons. Please check the picture below: Volume Adjustment: ▽...
40W Power Amplifier IR receiver, works together 3.5mm jack with the IR remote. Please Insert it into the point the IR remote at the IR specialized PA3 receiver when use, to avoid socket (3.5mm), to getting out of control as there connect the IR is no signal detected.
Page 13
40W Power Amplifier Uninstallation Delete all the control software files in corresponding file path.
40W Power Amplifier 4.3.3 Running Environment While the control software is installed, we can activate the software through the RS232 port and set the parameters, to make it able to send RS232 commands to control 40 Watt Power Amplifier. 4.3.4 Function Settings With the control software, we can easily switch the input channel, mute the output, check the working status, and adjust the volume etc.
40W Power Amplifier 4.3.5 RS232 Communication Commands Communication Protocol: RS232 Communication Protocol Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none Command Function Description Feedback Code 1A1. Switching the audio to input 1 A: 1 -> 1 2A1.
Page 16
40W Power Amplifier Notice: 1. The letter inside bracket [ ] is the variable code, which is changeable. 2. The bracket [ ] is not included to the RS232 commands. 3. Any dot “.” after the letters is part of the commands. 4.
40W Power Amplifier 7. Troubleshooting and Maintenance Problems Causes Solutions Check input/ output signal No signal at input/ output by an oscilloscope or a multimeter. No output audio Failed cable connection Change for another cable. Send it to the dealer for Broken unit repairing.
40W Power Amplifier 8. After-sales Service 1) If there appear some problems when running 40 Watt Power Amplifier, please check and deal with the problems reference to this user manual. Any transport costs are borne by the users during the warranty. 2) You can email to our after-sales department or make a call, please tell us the following information about your cases.