Coleman 2000000583 Installation Instructions

Before you begin

Read all instructions before set up.
• Select a level campsite clear of rocks, branches, and other hard
or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees.
• For best results in windy conditions, position end of tent into
the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the tent.

Parts and Components

Description
Hub (1)
Short Ridge Pole (2)
Long Leg Pole (2)
Short Leg Pole (4)
Long Ridge Pole (4)
Awning Pole (2)
Rainfly (1)
Short Ridge Poles (2)
Long Leg Poles (2)
Short Leg
Poles (4)
Long Ridge
Poles (4)
Awning Poles (2)

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
2. Insert the two Short Ridge Poles (with sticker dots) into the
sleeves (perpendicular to door) on top of tent. (Fig. 2)
3. Assemble four, shock-
corded, Long Ridge
Poles and insert into
the four diagonal corner
sleeves. (Fig. 2)
4. Insert end of first Short Ridge Pole (with
dot) into flange with a dot on Hub (Fig. 3).
Repeat for remaining Short Ridge Pole on
opposite flange of Hub with a dot.
NOTE: When installed properly, the loop on
the bottom of the Hub will be parallel
two Short Ridge Poles.
5. Insert four remaining Long Ridge Poles into Hub. (Fig. 4)
Tab
Fig. 4
OASIS TM CABIN TENT
Part Number
5010000120
5010000121
5010000122
5010000123
5010000124
5010000125
5010000126
Hub (1)
Doors
4 Long Ridge Poles
Fig. 2 2 Short Ridge Poles with Dots
Hub
Short Ridge
Pole with
Fig. 3
NOTE: Make sure tab on each
pole locks into slot on bottom
of Hub.
Hub
(Fig. 5)
Slot
Tab on
Pole
MODEL 2000000583
6. Snap hook at top of tent onto metal loop
on bottom of Hub. (Fig. 6)
7. Insert curved end of four Short
Leg Poles into the four Long
Ridge Poles on top of tent.
(Fig. 7)
NOTE: Make sure tab on each Long
Ridge Pole locks into slot on
each Short Leg Pole.
8. Insert curved end of two Long Leg Poles (with dots) into the
Short Ridge Poles at front & back of tent. (Fig. 8)
NOTE: Make sure tab on each Short Ridge Pole locks into slot
on each Long Leg Pole.
Short Leg Poles
Long Leg Pole
9. Raise tent by assembling shock-corded sections of each
Long and Short Leg Pole and inserting into curved ends of
Leg Poles. (Fig. 9)
10. Insert pin on loop at
each corner and the
Fig. 1
front and back of tent
into all six Leg Poles.
(Fig. 10)
11. Locate both plastic hooks at each corner,
and front and back of tent, then snap
onto Leg Poles to attach. (Fig. 11)
12. Drive stakes through rings, located on
four corners and front and back of tent,
at an angle for better anchoring.
(Fig. 12)

To Attach Rainfly

1. Drape Rainfly over
Dot
tent. Make sure
seams on Rainfly
are facing down
with web pockets
and long straps
centered over doors
& back of tent.
(Fig. 13)
2. Locate and wrap hook and
loop fasteners, on underside of
Tab
Locked
Rainfly, and wrap around the
Leg Poles to secure. (Fig. 14)
Fig. 5
Long Leg Pole (with Dots)
(Front of Tent)
(with Dots)
Fig. 9
(continued on other side)
Fig. 6
Fig. 7
Short Leg Poles
Fig. 8
Fig. 10
Pin & Loop on web tent strap
Fig. 11
Fig. 12
Rainfly
Long Strap
Fig. 13
Hook and Loop
Fastener
Fig. 14