Table of Contents
Advertisement
PREPARING & USING
THE NINJA HOT & COLD BREW SYSTEM™ – CONT.
FILLING THE TEA BREW BASKET
For best results, use the tea measurement
chart to determine how many tea bags or
how much loose leaf tea to use for each
brew size. The amount of tea for each size
will remain the same for any brew type
you select.
1 Open the brew basket by sliding it out
of the brewer. Ensure you have the TEA
filter holder in the machine, denoted by
the green handle with the tea leaf icon.
2 Place the tea permanent filter in the
TEA filter holder. The permanent filter
will make an audible click when properly
inserted. When using tea bags, you may
remove the tea permanent filter if more
space is needed in the brew basket.
3 Use the Ninja Smart Scoop™ and follow
the recommended measurements in the
chart to fill the brew basket, adjusting
to your preferred taste.
4 Slide the brew basket back into the
brewer until it clicks into place.
12 1-877-646-5288
AUTOMATIC DRIP STOP
The system is equipped with an automatic
drip stop. When the Drip Stop button
illuminated, the drip stop is closed and no
coffee or tea will flow out of the brew basket.
When brewing a half or full carafe, press
the Drip Stop button
to pause the brew
cycle and pour a cup. Promptly replace the
carafe and press the Drip Stop button
again to complete the brew. .
NOTE: If you forget to press the Drip
Stop button
to resume the brew,
the unit will pause the brew, and after
30 seconds it will give you a friendly
audible reminder. After 5 minutes, the
brew will be canceled.
DRIP STOP TIME SETTTING
After a brew is complete, the drip stop will
automatically close. Some types of coffee,
such as finely ground or decaf, can take
a little longer to fully drain from the brew
basket. To extend the amount of time the
drip stop remains open after a brew,
follow these instructions:
1 Press and hold the Drip Stop button
until the clock display flashes either dFLt
(default) or the previously specified time.
2 Press either the hour (H) or minute (M)
button until the desired extension time is
shown: dFLt (default), :15 (+15 seconds),
:30 (+30 seconds), :45 (+45 seconds),
:60 (+60 seconds), or OFF.
3 Press the Drip Stop button
to set
the new time. Or wait 5 seconds, and the
unit will beep, signifying that the new
extension time has been set.
NOTE: The setting you choose will
is
apply to both Coffee and Tea.
NOTE: When OFF is selected, the drip
stop will remain open after a brew is
complete. You can close the Drip Stop
at any time by pressing the Drip Stop
button
again. dFLt (default) is the
machine's default time setting.
INTELLIGENT WARMING PLATE
The Intelligent Warming Plate will
automatically turn on during a Half or
Full Carafe size of Classic or Rich Brew.
when brewing Coffee or Tea. The
Intelligent Warming Plate will adjust the
heat it produces to avoid burning the
coffee over time.
IMPORTANT: The
indicatorwill
illuminate when the warming plate is hot.
STAY WARM BUTTON
Press STAY WARM after the brew to turn
the Intelligent Warming Plate off. You can
turn the Intelligent Warming Plate back on
by pressing STAY WARM again.
TIME & TEMPERATURE ADJUSTMENT
You can adjust how long the Intelligent
Warming Plate remains on (up to 4 hours)
and/or set the temperature to High or Low.
By default, the Intelligent Warming Plate is
set to remain on for 2 hours, and is set to
High to keep your coffee and tea hot. The
Low setting keeps your brew at a slightly
lower temperature to preserve flavor longer.
NOTE: The setting you choose will
apply to both Coffee and Tea.
To change the time/temperature settings of
your warming plate, follow these instructions:
1 Press and hold STAY WARM until
the clock begins to flash the current
warming time.
2 Quickly press the hour (H) and/or
minute (M) buttons to increase the time
up to 4 hours or decrease the time to
0 hours. Press STAY WARM to set the
new time. Or wait 5 seconds, and the
unit will beep, signifying the new time
has been set.
3 Next, the clock will display the current
warming plate temperature. To keep the
same temperature, press STAY WARM, or
wait 5 seconds for the same temperature
to lock in. To change the temperature,
press the hour (H) or (M) buttons, then
press STAY WARM, or wait 5 seconds for
the temperature to lock in.
NOTE: If you set the warming time
to 0 hours, it will skip the warming
temperature menu. When set to 0
hours, Stay Warm will not automatically
activate during or after a carafe brew
cycle, but you can still turn it on manually
by pressing STAY WARM again.
ninjakitchen.com
13
Advertisement
Table of Contents
