Advertisement
Quick Links
Advertisement
Related Manuals for Flebi SUPRA 3.0
Summary of Contents for Flebi SUPRA 3.0
- Page 1 User Manual...
- Page 2 6. Use of Nexus 3 changes 18. Handlebar folding mechanism 19. Quick fold easy-folding Electrical operation 20. Drag on the training wheels 7. Removal and insertion of the battery Parts of Flebi Supra 3.0 8. Battery recharge 21. Discovering your Flebi 9. C300U display operation...
-
Page 3: Box Contents
Unpacking and Assembly Box contents Assembling your Flebi Supra 3.0 is very easy! - Take the bike out of the box - Remove the protections - Save the battery keys - Unfold the bike (see 14) - Insert the handlebar assembly (see 2) - Page 4 Unpacking and Assembly Introduction of the seat handlebar To install the assembly made up of the handlebar and the telescopic seatpost that allows you to adjust the height, you simply have to insert it into the stem of the handlebar following the guides that you'll find.
- Page 5 Packing in original box In the event that you have to repackage your bike in its original box to send it to Flebi's technical service, we recommend that you follow the steps below to protect it as best as possible and avoid...
- Page 6 Puesta en marcha Insertion and adjustment of the handlebar telescopic You can adjust the height of the handlebar to accommodate your height. To do this, open the telescopic closure and place the seatpost in the desired position, taking care not to exceed the safety mark.
- Page 7 Start up Disc brake adjustment Tektro To adjust the mechanical disc brake, we will first loosen the mounting bolts, to allow some movement for the caliper. Then, you will have to act on the regulator of the pad on the inside. Finally, you must press the brake to take up the slack in the cable and thus compress the caliper on the disc to align...
- Page 8 Start up Use of Nexus 3 changes Supra 3.0 features Shimano Nexus 3 speed gears, integrated into the rear wheel hub. This system allows to change stationary without the chain coming out or crossing. The changes, in fist mode, will help you overcome any obstacle.
- Page 9 Electrical operation Removal and insertion of the battery Supra 3.0 battery can be removed to recharge off the bike, or to be replaced with another. To remove it from the box, you just have to open the security lock with one of the keys, and then carefully pull the ring.
-
Page 10: Recharging The Battery
Electrical operation Recharging the battery The Supra 3.0 battery can be recharged both inside the frame (uncovering the triangular cover to access the connector) and outside of it. In both cases you must plug the charger into the mains, and the charger connector to the battery. - Page 11 Electrical operation C300U display operation The C300U LCD display is activated by pressing the power button M located in the center of it. To run the bike, you must turn on the battery. Once turned on, we will have several fields: speed, engine load, battery, assistance levels (6), etc.
- Page 12 Electrical operation C500B display operation The C500B LCD display is activated by pressing the Power button located on the top of it. To run the bike, you must turn on the battery. Once turned on, we will have several fields: speed, mode, engine...
- Page 13 Electrical operation C200S display operation The C200S LCD display is activated by pressing the power button located at the bottom of it. Once turned on, at the top is a 5-bar indicator that shows the remaining battery level. Just below are the 3 levels of pedal assistance available: HIGH, MEDIUM and LOW.
- Page 14 Electrical operation Accelerator operation (optional) El The throttle on the Supra 3.0 has the same operation and installation as on the Supra ECO. Unlike the PAS (Pedal Assist System), the accelerator makes the motor work without the need to pedal.
- Page 15 Folding & Unfolding Unfolding the bike The steps to unfold your Flebi Supra 3.0 are: - Place the seat post inside the frame - Unfold the frame, tighten the front closure and place the safety (see 15) - Raise the stem of the handlebar, close the...
-
Page 16: Folding The Bike
Folding & Unfolding Folding the bike The steps to fold your Flebi Supra 3.0 are: - Release the swingarm by pressing the lever next to the yellow elastometer (see 14) - Remove the safety and release the front folding lever to then open the frame (see... -
Page 17: Swingarm Operation
Folding & Unfolding Swingarm operation One of the main advantages of Supra 3.0 is its comfortable and effective folding mechanism, since with a simple movement you can semi-fold and reduce its length by half, very practical for rolling it. To do this, you just have to act on the folding lever located on the back. - Page 18 Folding & Unfolding Opening/Closing the frame To open or close the front of the frame, you just have to remove the safety in case of opening it and put it in case of closing it. And release the lever of the fold out to open it, and press it inward to close it.
- Page 19 Folding & Unfolding Folding/Unfolding the pedals Wellgo To fold or unfold each Wellgo pedal you must press the control outwards and, at the same time, bend the pedal inwards (folded) or outwards (unfolded) until you feel the clic. Video: https://youtu.be/V55_kJvUzy8...
- Page 20 Folding & Unfolding Handlebar folding mechanism First make sure the cables are not too tight due to the fixed handlebar height. To fold the handlebar stem, you must remove the lever lock and open it by pressing outwards to then lower the power.
- Page 21 Folding & Unfolding Quick easy-folding This folding system is an alternative to the conventional one, which has the advantage of being faster (2 steps instead of 3), and reducing the width of the folded bike as much as possible, sacrificing length. The procedure is the same as the anterior (see 16), without folding the frame at the joint.
- Page 22 Folding & Unfolding Drag on the training wheels Drag int semi-folded Drag in trolley type position position Video: https://youtu.be/4wmW9G9_VrQ...
- Page 23 Partes de la Flebi Supra 3.0 Descubre tu Flebi Info: https://www.flebi.com/...