Table of Contents
Advertisement
1.6 DISASSEMBLY/ASSEMBLY OF 5OP BLOCK
ASSEMBLY/CCD BOARD ASSEMBLY
1.6.1 Precautions
1. Take care in handling the CCD image sensor, optical LPF
and lens components when performing maintenance
etc., especially with regard to surface contamination, at-
tached dust or scratching. If fingerprints are present on
the surface they should be wiped away using either a
silicon paper, clean chamois or the cleaning cloth.
2. The CCD image sensor may have been shipped with a
protective sheet attached to the transmitting glass. When
replacing the CCD image sensor, do not peel off this
sheet from the new part until immediately before it is
mounted in the OP Block Assembly.
3. The orientation of the optical LPF is an important factor
for installation. If there is some marking on the LPF, be
sure to note it down before removing and to reassem-
ble it very carefully as it was referring to the marking.
1.6.2 How to remove CCD board assembly and CCD
base assembly
1. Unsolder the CCD board assembly by the 14 points
(SD5) and then remove it.
2. Remove the two screws (1, 2) and remove the CCD base
assembly.
5
Note
a: When removing the CCD base assembly, pay
heed to the CCD image sensor because the
spacer rubber and optical LPF are occasionally
removed together with the CCD image sensor.
5
Note
b: When replacing the CCD image sensor, don't re-
place it individually but replace the CCD base as-
sembly in whole with a new one.
∗
(S
3
(S
5
b)
ZOOM MOTOR
NOTE
(S
Blue
NOTE
e
5
∗
IRIS MOTOR
4
UNIT
OP
5
b)
side
OP BLOCK
∗
5
(S
c)
5
5
d
∗
6
(S
5
c)
∗
∗
9
8
(S
5
c)
5
c)
1.6.3 How to assemble CCD base assembly and CCD
board assembly
1. Install the optical LPF with the spacer rubber attached
to its CCD side in the OP block assembly.
5
Note
c: Pay careful attention to the orientation of the LPF.
2. Set the CCD base assembly with careful attention to the
spacer rubber not to come off the right position, and fas-
ten them together with the two screws (1, 2).
3. Set the CCD board assembly in the CCD base assem-
bly, and then solder it by the 14 points (SD5).
1.6.4 Replacement of Service Repair Parts
The service repair parts for the OP Block Assembly are as
listed below.
Before replacement of these parts, remove the bracket (OP
assembly) as required.
Take special care not to disconnect any of the FPC wires or
cause any damage due to soldering (excessive heating).
1. Focusing motor
2. Zoom motor
3. Iris motor unit
5
Note
d: When replacing the focusing motor or the zoom
motor, solder the FPC at a space of about 1 mm
above the terminal pin.
5
Note
e: The iris motor unit includes the FPC Assembly and
two sensors.
CCD
side
(S
CCD SPACER
OPTICAL
SPACER
LPF
RUBBER
NOTE
c
NOTE
5
5
FOCUS MOTOR
NOTE
5
∗
11
∗
(S
5
c)
10
(S
5
c)
∗
7
∗
: 0.118 N
(S
c)
5
Fig. 1-6-1
(SD 5 )
∗
1
5
a)
∗
CCD BOARD
2
ASSY
(S
5
a)
CCD BASE
ASSY
NOTE
5
b
a
d
m (1.2 kgf
cm)
•
•
1-11
Advertisement
Table of Contents
