Related Manuals for Taiwan Commate Computer Inc. P4BEA
Summary of Contents for Taiwan Commate Computer Inc. P4BEA
- Page 1 P4BEA User’s Manual P4BEA Motherboard User’ s Manual Product Name: P4BEA Manual Revision: English, 1.0...
- Page 2 P4BEA User’s Manual Trademarks Intel, Socket 478, Pentium 4, Pentium 4 Celeron, Willamette and Northwood, 478-pin FC-PGA2 CPU are trademarks of Intel Corporation Award is a trademark of Pheonix/Award Software International Inc. MS-DOS, Windows 95, Windows 98, Windows ME, Windows XP, Windows 2000 and...
-
Page 3: Table Of Contents
P4BEA User’s Manual Table of Contents CHAPTER 1 INTRODUCTION........... 5 Product Overview ..................5 Features ......................6 Specifications ....................6 Packing List....................9 MotherBoard Layout..................10 CHAPTER 2 HARDWARE SETUP.......... 11 Installation Procedure.................11 2.1.1 Jumper Settings ...................11 2.1.2 CMOS Operation(JRTC)................12 2.1.3 Keyboard Voltage Setting................13 2.1.4 CPU FSB Frequency Setting..............14... - Page 4 P4BEA User’s Manual 2.4.10 Serial Port (9-pin D-Sub. COM1) ..............23 2.4.11 Parallel Port (25-pin D-Sub. PRINTER)...........23 2.4.12 USB Connectors (USB1 & USB2).............24 2.4.13 LAN Connector.....................24 2.4.14 ACT/LNK LED (Green color)..............24 2.4.15 Speed LED (Orange color).................24 2.4.16 Line Out Connector..................24 2.4.17 Line In Connector..................24...
-
Page 5: Chapter 1 Introduction
Product Overview Thanks for your purchasing the P4BEA motherboard. The new generation, 478-pin FC-PGA2 motherboard P4BEA supports a full range of the latest generation Intel Pentium 4 processors .The leading edge chipset Intel Brookdale 82C845E MCH and FW82801DB ICH4 is designed for working with Pentium 4(1.4GHz-2.53GHz), Pentium 4 Celeron, Willamette and Northwood processor in the 478-pin package based on the VRM 9.0 Spec. -
Page 6: Features
P4BEA User’s Manual Features • Wake up on LAN. • Wake on Keyboard. • Modem Remote Ring On. • Support NCR SCSI BIOS. • Support Suspend to RAM. • Support Ultra DMA 33/66/100. • Support Hardware Monitor function. • Realtek ALC201A Audio CODEC on board. - Page 7 P4BEA User’s Manual DIMM: • Supports 2.5V PC1600/2100 compliant DDR DRAM in 2 184-pin banks, each bank consists of 1x184-pin DIMM socket, which can support memory sizes of 64/128/256/512MB/1GB modules. • Supports 4-banks up to 2.0GB DRAM for unbuffered DDR DRAM module.
- Page 8 P4BEA User’s Manual • 18-bit Stereo Full-Duplex. • Full Duplex Variable Sample Rates from 7kHz to 48kHz with 1Hz Resolution • Take advantage of CPU to implement audio synthesis and 3D effects processing • Stereo Headphone Amplifier • Three Analog Line-Level Stereo Inputs for LINE-IN, CDIN and AUX •...
-
Page 9: Packing List
P4BEA User’s Manual • Supports Wake up on LAN • Supports Keyboard Wake-Up Operating System : • Supports Windows 3.x/95/98/ME/2000/XP, Windows NT, MS-DOS V6.22, OS/2, Novell, Unix, SCO UNIX, etc. Dimension : • 305 x 210 mm (W x L) at ATX Form Factor... -
Page 10: Motherboard Layout
P4BEA User’s Manual MotherBoard Layout JFRNT USBC USBB JWOL BIOS JRTC ICH4 CDIN JLAN JFSB Intel 845E PWRFAN CPUFAN JKBV... -
Page 11: Chapter 2 Hardware Setup
P4BEA User’s Manual Chapter 2 Hardware Setup Installation Procedure 1. Jumper settings 2. Installation of CPU 3. Installation of Memory 4. I/O Connections & Panel Connections 2.1.1 Jumper Settings Reset the Function of Flash CMOS JRTC Sets the Keyboard Voltage... -
Page 12: Cmos Operation(Jrtc)
P4BEA User’s Manual 2.1.2 CMOS Operation(JRTC) How to Clear the CMOS Setting Turn off the power. Remove ATX power cable from connector J1. Remove Jumper Cap from JRTC (2-3) and put on JRTC (1-2) to remove the CMOS setting. Remove Jumper Cap from JRTC (1-2) and put on JRTC (2-3). -
Page 13: Keyboard Voltage Setting
P4BEA User’s Manual 2.1.3 Keyboard Voltage Setting This motherboard supports wake on keyboard function. This feature requires that your system have an ATX power supply with at least 300mA +5V standby power and set this jumper to 2 & 3 pin short. -
Page 14: Cpu Fsb Frequency Setting
P4BEA User’s Manual 2.1.4 CPU FSB Frequency Setting The JFSB jumper provides FSB frequency settings for the CPU. Auto Detect, 400MHz or 533MHz FSB frequency can be selected with this jumper. The over specification operation is not recommended. Default setting in the 400MHz FSB Frequency. -
Page 15: Lan Enable / Disable Setting (Jlan)
P4BEA User’s Manual 2.1.6 LAN Enable / Disable Setting (JLAN) . Supports LAN function. You can set the LAN function with JLAN jumper. JLAN Disabled Enabled(Default) JLAN... -
Page 16: Installation Of Cpu (For Socket 478 Cpu)
P4BEA User’s Manual Installation of CPU (For Socket 478 CPU) Before installing CPU, make sure the power is off. Locate the level bar on the mPGA478 ZIF socket. Push level bar away from the socket and pull upward 90 degrees. Insert the CPU into the socket. -
Page 17: Memory Configuration
P4BEA User’s Manual 2.3.3 Memory Configuration There is no jumper setting required for the memory size or type. It is automatically detected by the system BIOS, and the total memory size is to add them together DIMM Socket DIMM Modules... -
Page 18: Atx Power Connector (20-Pin Atxpwr)
P4BEA User’s Manual 2.4.1 ATX Power Connector (20-pin ATXPWR) Make sure that the power supply is off before connecting or disconnecting the power cable. PIN assignment 3.3V 3.3V 3.3V -12V PS_ON PW_OK 5V_SB This connector (ATXR1) supplies theCPU operation voltage (Vcore) , be sure to insert below power connector in your motherboard. -
Page 19: Cpu, Chassis Fan Connector (3-Pin Cpufan, Chasfan)
P4BEA User’s Manual 2.4.2 CPU, Chassis Fan Connector (3-pin CPUFAN, CHASFAN) Connect the fan's plug to the board taking into consideration the polarity of the connector. Pin assignment +12V FAN_CTL CPUFAN/CHASFAN 3 2 1... -
Page 20: Infrared Connector ( 5*2-Pin Jir )
P4BEA User’s Manual 2.4.3 Infrared Connector ( 5*2-pin JIR ) This connector supports the optional wireless transmitting and receiving infrared module, with this module and application software such as Laplink or Win95 Direct Cable Connection, user can transfer files to or from their laptops, notebooks, PDA, PCs and printers. -
Page 21: Wake On Lan Connector (3-Pin Jwol)
P4BEA User’s Manual 2.4.4 Wake on LAN Connector (3-pin JWOL) The JWOL connector powers up the system when a wakeup packet or signal is received from the network. This feature requires the Wake up on LAN function in BIOS is set to Enabled and that your system has an ATX power supply with at least 720mA +5V standby power. -
Page 22: Floppy Disk Drive Connector (34-Pin Floppy)
P4BEA User’s Manual 2.4.5 Floppy Disk Drive Connector (34-pin FLOPPY) This connector supports the provided floppy disk drive ribbon cable. Orient the red stripe to pin 1 2.4.6 Primary/Secondary IDE Connector (Two 40-pin IDE) These connectors support the provided IDE hard disk ribbon cable. Connect your first IDE hard disk to master mode of the primary channel. -
Page 23: Back I/O Panel Introduction
P4BEA User’s Manual 2.4.7 Back I/O Panel Introduction PS/2 MS LAN PRINTER PORT GAMEPORT PS/2 KB USB1/2 COM1 COM2 LINE OUT LINE IN MIC 2.4.8 PS/2 Mouse Port (6-pin Mini-Din MS) The system will direct IRQ12 to the PS/2 mouse. -
Page 24: Usb Connectors (Usb1 & Usb2)
P4BEA User’s Manual 2.4.12 USB Connectors (USB1 & USB2) You can attach USB devices to the USB1 or USB2 connector. 2.4.13 LAN Connector The LAN Connector is used to attach RJ-45 cable. For 100Base-TX, your network cable must be category 5, twisted-pair wiring with RJ-45 connectors. If you plan on running the adapter at 100Mbps, it must be connected to a 100Base-TX hub. -
Page 25: Game/Midi Port
P4BEA User’s Manual 2.4.19 Game/MIDI Port The Game/MIDI Port connector is used to attach a joystick for game interaction or to attach an external MIDI device for playback, mixing, or recording. 2.4.20 CDIN Audio (4-pin Black color Connector) The CD_ROM Audio connector is used to connect the audio cable from either an ATAPI IDE or Sony CD-ROM drive for playback, mixing, and recording. -
Page 26: Panel Connection (24-Pin Jfrnt)
P4BEA User’s Manual 2.4.21 Panel Connection (24-pin JFRNT) JFRNT Connector Function GREENLED Suspend Mode LED PWRLED Power LED KEYLK Keylock Switch SPKR Speaker RESET Reset Switch IDELED HDD LED PWRBNT ATX Power Button Connector SMI Switch Sleep Switch WARNING: To avoid the system from failing, turn off the power before connecting any... - Page 27 P4BEA User’s Manual JFRNT Pin assignment ACPI+ Vcc(+) Green Reset KBLOCK Power Vcc(+) Reset Active PWRBT 10 GND Keyboard Lock 11 GND SPKIN 12 SMI Power Speaker Switch Switch...
- Page 28 P4BEA User’s Manual...