Table of Contents
Advertisement
New Era Pump Systems Inc.
General Information
1.
Thank you for purchasing the Syringe Heater Kit. Please familiarize yourself with the Syringe Heater's operation by reading this
user's manual. For future reference, record the serial number, located on the bottom identification label, and the date of purchase.
New Era Pump Systems Inc., located in Farmingdale, NY USA, can be contacted at:
Phone: (631) 249-1392
www.SyringePump.com
This Operating Manual, and the Syringe Heater's hardware, electronics, and firmware are copyrighted.
Copyright 2012-2020, all rights reserved.
1.1
Warnings
!
!
Read the user's manual
!
Risk of electrical shock. Do not cut heating pads.
!
Surface of heating pads can get very hot
!
No user serviceable parts are inside.
!
Disconnect power from the heater when connecting or
disconnecting cables.
!
Do not immerse the heater control unit or pads in liquid
!
Install on a stable surface.
!
The heater can automatically start when the heater is
operating or when attached to an external control device.
1.2
Disclaimer
New Era Pump Systems Inc. makes no representations or warranties, expressed, statutory or implied,
regarding the fitness or merchantability of this product for any particular purpose. Further, New Era Pump
Systems Inc. is not liable for any damages, including but not limited to, lost profits, lost savings, or other
incidental or consequential damages arising from ownership or use of this product, or for any delay in the
performance of its obligations under the warranty due to causes beyond its control. New Era Pump
Systems Inc. also reserves the right to make any improvements or modifications to the product described in
this manual at any time, without notice of these changes.
New Era Pump Systems Inc. products are not designed, intended, or authorized for use in applications or as
system components intended to support or sustain human life, as a clinical medical device for humans, or
for any application in which the failure of the product could create a situation where personal injury or
death may occur.
All brand and product names used in this manual are the trademarks of their respective owners.
1.3
Warranty
New Era Pump Systems Inc. warranties this product and accessories for a period of two years, parts and
labor, from the date of purchase. The repaired unit will be covered for the period of the remainder of the
original warranty or 90 days, whichever is greater.
A return authorization number must be obtained from New Era Pump Systems Inc. before returning a unit
for repair. Warranty covered repairs will not be performed without a return authorization number. At the
option of New Era Pump Systems Inc., a defective unit will be either repaired or replaced.
This warranty does not cover damage by any cause including, but not limited to, any malfunction, defect or
failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary
to furnished instructions, shipping or transit accidents, modifications or repair by the user, harsh
environments, misuse, neglect, abuse, accident, incorrect line voltage, fire, flood, other natural disasters, or
normal wear and tear. Changes or modifications not approved by New Era Pump Systems Inc. could void
the warranty.
The foregoing is in lieu of all other expressed warranties and New Era Pump Systems Inc. does not assume
or authorize any party to assume for it any other obligation or liability.
Publication #1200-01
www.SyringeHeater.com
FAX: (707) 248-2089 Email:
www.SyringeHeater.com
and Cautions !
1
Model HEATER-KIT-1
INFO@SYRINGEPUMP.COM
!
Prevent liquids from entering openings.
!
Only connect to a power source as specified on
the power supply label.
!
Do not push objects of any kind into openings,
except for appropriate cables and connectors.
!
If the heater becomes damaged, do not use unless
certified safe by a qualified technician. Damage
includes, but is not excluded to, frayed cords and
deterioration in performance.
!
Discharge static from control cables before
connecting by touching the cable to ground.
12/25/20
Advertisement
Table of Contents
