Using The " Vertical Shot; Using The " Spray; Electronic 3-Way Auto Shut-Off Function(Ni-S630 Only); How To Care For And Store Your Iron - Panasonic NI-S530 Operating Instructions Manual

Using the " vertical shot "

To get better results
when using vertical
steam, hang the
garment on a hanger.
Curtains and drapes
may also be steamed
once they are hung.
Hold the iron away from
your body, close to but
not touching the fabric. Pull the fabric tightly and pump
the power shot button at 2 seconds intervals as you press
the iron over the wrinkled fabric.
• If the power shot weakens, wait until the thermostat
operating indicator light goes on, and then off.

Using the " spray "

The spray feature is particularly helpful for removing stubborn
wrinkles and where extra dampen is needed.
The spray may be used with steam or dry ironing.
Simply push the spray mist button whenever spray is
desired.
• If the spray does not work
immediately, keep triggering
until it does.
14
NI-S630,S530,S430 [i8200Q-oS43A]_说明书_EN,VN,AR.indb 9 NI-S630,S530,S430 [i8200Q-oS43A]_说明书_EN,VN,AR.indb 9
Electronic 3-way auto shut-off function
(NI-S630 only)
The auto shut-off feature is not intended to take the place of
unplugging the cord. The auto shut-off system works
regardless of the position of the temperature selector.
1. When the iron is left idle with its soleplate facing down or on
its side for approx. 1 minutes, the iron will automatically shut
off.
2. When the iron is left idle on its heel rest for approx.10
minutes, the iron will automatically shut off.
3. To resume ironing and turn the iron on, simply move the iron
in any manner. If the iron has been left in the auto shut off
mode for more than 10 minutes, allow the iron to reheat
until the indicator light goes off.
10 minute to " 0 "
1 minute to " 0 " 1 minute to " 0 "
Always unplug the iron when you finish ironing. Even though
the Iron is unplugged, the soleplate is still hot. Make sure to
rest the iron on its heel, away from fabric.

How to care for and store your iron

Cleaning
►Using the " power shot " feature
1. Fill the water reservoir with tap water as described in the
" How to use as an iron " on P11.
2. Set the temperature select indicator
to " 0 ".
3. Plug the power plug into socket-outlet.
4. Stand the iron up and set the temperature
select ndicator to " MAX ".
5. Hold the iron horizontally over the sink after the thermostat
operating indicator light has gone out.
6. Pump the power shot button quickly
(at least 3 times per second) for
approx. 20-30 times continuously. While
pumping, shake the iron back and forth.
7. Set the temperature select
indicator to " 0 ".
8. Unplug and dispose of any water
remaining in the water reservoir.
9. To prevent corrosion of the soleplate vents, plug the power
plug into a socket-outlet, stand the iron up, set the
temperature select indicator to " MAX " and preheat for
about 5 minutes.
10.Set the temperature select indicator to " 0 " and unplug.
11.Iron on a used cloth to remove any impurities on the
soleplate.
• Repeat the steps if venting of the steam does not improve.
• Use both methods once every two weeks. If the water is very
hard (i.e. steam holes on the soleplate are easily blocked by
impurities), both methods should be used more frequently.
• Let the iron cool down on its heel rest and follow the
instructions in the " After each use " on P12.
►Anti calc system (Stay clean vents)
The built-in anti calc system in the water reservoir
continuously reduces scale build up in the vaporizing chamber
of the iron.
This system makes it possible to use the steam function for a
long period of time and prevents steam vents from clogging.
2022/4/29 11:05:03 2022/4/29 11:05:03
15