Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dali HRYXJ-F5
Summary of Contents for Dali HRYXJ-F5
- Page 1 Zhejiang Dali Technology Co., Ltd. Address: 639 Binkang Road, Binjiang District, Hangzhou National Service Hotline: 4008871897 Sales Service Hotline: 0571-86695666 Fax: 0571-86695600 Postal Code: 310053 E-mail: market@dali-tech.com Website: www.dali-tech.com...
- Page 2 HRYXJ-F5 Thermal Infrared Imager For Fire Protection User Manual Zhejiang Dali Technology Co., Ltd.
- Page 3 Warning! In a dark and smoky environment, firemen can utilize the functions of HRYXJ-F5 thermal infrared imager for fire protection (hereinafter referred to as F5) to the fullest to make a better judgment about such harsh environment and take actions in a more efficient way. Users must read and understand the following information carefully;...
- Page 4 Thank you very much for choosing HRYXJ-F5 thermal infrared imager for fire protection. HRYXJ-F5 thermal infrared imager for fire protection is specially designed for assisting firemen in search and rescue in a smoky or dark environment with low visibility, which meets requirements of China’s public safety industry standard GA/T 635—2006 Thermal Infrared Imager for Fire Protection.
-
Page 5: Quick Start
1.1 Quick Start Please start operation as follows: 1. Prior to start of the thermal infrared imager for the first time, charge the battery for 3 hours or until the green battery status indicator lights up. 2. Long press on the power button to turn on the thermal infrared imager. 3. -
Page 6: Function Buttons
2 Introduction to Thermal Infrared Imager 2.1 Function Buttons [1] The “Power” Button The power button has the following two functions. a) The power button can be used for turning on and turning off the thermal infrared imager. Press this button for more than 3 seconds to turn on/turn off the thermal infrared imager. - Page 7 2.2 Port and Indicator [1] Device Contact This contact is connected to the charging dock and is used for data transmission and charging. [2] Indicator Light This indicator light is used as power indicator light and charging status indicator light. After the device is turned on, the power indicator light is green.
-
Page 8: Screen Elements
3 Screen Elements 3.1 User Interface [1] Company logo: The logo of Dali Technology. [2] Laser ranging display: The result of the last laser ranging can be displayed. [3] WIFI display: The WIFI display appears after WIFI is turned on and disappears when WIFI is turned off. -
Page 9: Basic Operation
4 Basic Operation 4.1 Battery Installation & Removal To remove the battery, unscrew the battery knob firstly (a one-yuan coin or other tools with the same thickness may be used) and then open the battery cover Battery Knob to remove the battery. To install the battery, place the battery into the device with the metal contact facing the inside of the device, then close the battery cover... - Page 10 General Instructions on Safe Battery Use 1. The battery should be stored at an ambient temperature of -20 °C to 20 °C, because the battery has a small amount of self-discharge during storage. In order to avoid any impact on battery capacity due to possible over-discharge of the battery during storage, the battery should be fully charged when being put into storage and then be charged at regular intervals.
- Page 11 4.5 Selection among Color Mark Modes The thermal infrared imager has six different color mark modes. Short press on the “Power” button to switch among color mark modes. 4.5.1 The Iron Red Mode The iron red mode is the default mode of the thermal infrared imager.
- Page 12 4.5.4 The Firefighting Mode The firefighting mode is similar to the basic mode; however, the thermal tinting mode is characterized by a higher starting temperature. This mode is suitable for fire scenes with relatively high background temperatures, especially for a fire scene characterized by a large number of open flames high-temperature...
- Page 13 4.7 The Zooming Function Short press on the “Zoom” button to zoom in or zoom out. The zooming factor X2/X4 will appear at the status display bar in the upper right corner of the screen. 4.8 Laser Ranging Short press on the “Trigger” button to trigger the laser ranging function. The distance value will be displayed in the upper left corner of the screen.
- Page 14 4.10 The WiFi Function Long press on the “Trigger” button to trigger the WiFi function, and the WiFi symbol can be displayed on the screen. The operator may access the thermal infrared imager via a wireless device such as mobile app to view the images displayed on the screen. 4.11 Saving Images Short press on the “Shooting”...
-
Page 15: Technical Specifications
5 Technical Specifications Item Technical Specifications Type Uncooled focal plane micro-heat type Resolution Ratio 384*288 Optical Data Detector Pixel Size 17um (Sensor) Spectral Response 8~14um Thermal Sensitivity (NETD) ≤60mK Frame Frequency (Refresh Rate) 50/60HZ Angle of View Field 49.2°*36.3° Optical Data Lens Focusing Range 0.5m -∞... - Page 16 6 Countermeasures for Common Malfunctions In case of any problem with your thermal infrared imager, please use the following table for troubleshooting. If the problem cannot be resolved, please disconnect the power supply and contact our maintenance department. Symptoms Causes & Solutions The battery isn’t installed or incorrectly installed.
Need help?
Do you have a question about the HRYXJ-F5 and is the answer not in the manual?
Questions and answers