Advertisement
Quick Links
1
DSLR Nano Handheld Camera Stabilizer Brace
Support
(FLCM-DN-ABQ)
A s s e m b l y M a n u a l
What's In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Central Post
Base Platform with 16 weight discs
Head, Mid & Bottom Plate
1 x washer
2 x Allen bolts
2 x knob
Quick Release
Camera Bolts
Size - 1/4", 3/8"
1 x Plastic screw driver
1 x L-Type Allen key (size-3mm)
V-shaped adapter
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permitted by the applicable copyright
statutes or in writing by the Publisher.
Advertisement
Related Manuals for Flycam FLCM-DN-ABQ
Summary of Contents for Flycam FLCM-DN-ABQ
- Page 1 DSLR Nano Handheld Camera Stabilizer Brace Support (FLCM-DN-ABQ) A s s e m b l y M a n u a l What’s In The Box Please inspect the contents of your shipped package to ensure you have received everything that is listed below.
-
Page 2: Head Assembly
Features Quick Release Head, Mid & Bottom Plate Central Post Base Platform with 16 weight discs Head Assembly Head Plate Mid Plate Bottom Plate... - Page 3 Handheld Steadycam with Base Platform Setup • Remove the cap from the middle of the base platform, and you will see 1/4 thread located in the center, as shown in the image. • Attach the extended part of the post via threaded insert at the bottom to the 1/4 screw present on the expandable base platform.
- Page 4 • Remove all the knobs of the head plate by loosening them. • Remove the head plate from the 3-piece head assembly in preparation to attach it to your camera. • Insert the bolt into the center hole of the top head plate, as shown in the image.
- Page 5 • Tighten the plate using both the side knobs. NOTE: If you wish to by pass the quick release plate, the camera (Not Included) can be directly attached to the Head Plate by using following assembly sequence (without quick release plate).
- Page 6 • Place the quick release adapter and the top plate by sliding them onto the middle plate. • Align the plate to the middle plate and secure the head plate and the middle plate with the help of four knobs. •...
- Page 7 Adding Weight Sand Positioning for Proper Balance Continuing the assembly and balance requirements to make your FLYCAM DSLR Nano fully functional you will note that the base platform has a provision to mount the balance weights in their cups via a slot found on both sides of the post.
- Page 8 When testing for horizontal balance start from a flat and level surface like a table. This will allow the FLYCAM DSLR Nano to hang freely as you hold it. If your FLYCAM DSLR Nano is correctly balanced on its horizontal axis, then it will be both level &...
- Page 9 • Remove the top plate of the Flycam and line up your camera so that its center of gravity is as close to the center of the plate as possible (basically hold the camera in your hand until it feels balanced both left and right as well as forward and back).
-
Page 10: Maintenance
• Hold the handle normally and turn the FLYCAM DSLR Nano so that it is horizontal to the ground. Let go of the stalk while keeping a firm grip on the handle and count how long it takes to return to vertical again. - Page 11 Cleaning Do not use solvents or harsh cleaners of any kind on your Flycam DSLR Nano. If the unit becomes dirty, use a damp soft cloth or sponge and a mild detergent to gently clean external parts. Storage • Should you need to store your FLYCAM DSLR Nano for a long period of time then place the unit upright in a dry or low to normal humidity area whenever possible.
- Page 12 YOUR FLYCAM DSLR NANO HANDHELD CAMERA STABILIZER ALL DRESSED UP AND READY TO GO! (SHOWN WITH OPTIONAL ACCESSORIES) Warranty: We offer one year warranty for our products from date of purchase. Within this period of time, we will repair it without charge for labor or parts. Warranty doesn’t cover transportation costs nor does it cover a product subjected to misuse or accidental damage.