Page 2
2.101(a) or as “Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent agency regulation or contract clause. Use, duplication or disclosure of Software is subject to Agilent Technologies’ standard commercial license terms, and non-DOD Departments and Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987).
Page 3
Safety Notes The following safety notes are used throughout this document. Familiarize yourself with each of these notes and its meaning before performing any of the procedures in this document. WARNING Warning denotes a hazard. It calls attention to a procedure which, if not correctly performed or adhered to, could result in injury or loss of life.
N9010/20/30AK-REA Description Description The Agilent N9010/20/30AK Option REA provides the capability to relocate the instrument disk drive from the internal drive drawer, to an external customer supplied enclosure. This is accomplished by installing an eSATA drive adapter into the CPU rear panel slot, normally occupied by the internal disk drive.
Inspect the shipping container. If the container or packing material is damaged, it should be kept until the contents of the shipment have been checked mechanically and electrically. If there is physical damage please notify the nearest Agilent Technologies office. Refer to “Agilent Support, Services, and Assistance” on page 12.
N9010/20/30AK-REA Hard Drive Disk or Solid State Drive Replacement Procedure Hard Drive Disk or Solid State Drive Replacement Procedure The hard disk drive and solid state disk drive will be referred to as HDD/SSD through out this document. Follow the appropriate Electrostatic Discharge (ESD) procedures. ESD can CAUTION damage or destroy electronic components.
N9010/20/30AK-REA Hard Drive Disk or Solid State Drive Replacement Procedure 3. Remove the 2.5 inch HDD/SSD from its tray assembly by removing the 4 screws. NOTE The tray assembly must be kept for use when returning the instrument for calibration or repair. 4.
Declaration of Conformity A copy of the Declaration of Conformity is available upon request, or a copy is available on the Agilent Technologies web site at http://regulations.corporate.agilent.com/DoC/search.htm Statement of Compliance This instrument has been designed and tested in accordance with CAN/CSA 22.2 No.
N9010/20/30AK-REA Safety and Regulatory Information Before Applying Power Verify that the premises electrical supply is within the range of the instrument. The instrument has an autoranging power supply. WARNING If this product is not used as specified, the protection provided by the equipment could be impaired.
Allow all residual alcohol moisture to evaporate, and fumes to dissipate prior to energizing the instrument. To prevent electrical shock, disconnect the WARNING Agilent Technologies from mains electrical supply before cleaning. Use N9010/20/30AK-REA a dry cloth or one slightly dampened with water to clean the external case parts.
N9010/20/30AK-REA Electrostatic Discharge Protection Electrostatic Discharge Protection Protection against electrostatic discharge (ESD) is essential while removing assemblies from or connecting cables to the instrument. Static electricity can build up on your body and can easily damage sensitive internal circuit elements when discharged. Static discharges too small to be felt can cause permanent damage.
N9010/20/30AK-REA Regulatory Information Regulatory Information This section contains information that is required by various government regulatory agencies. Instrument Markings The instruction documentation symbol. The product is marked with this symbol when it is necessary for the user to refer to the instructions in the documentation. This symbol indicates that the instrument requires alternating current (ac) input.
Regulatory Information Battery Collection Do not throw batteries away but collect as small chemical waste, or in accordance with your country’s requirements. You may return the battery to Agilent Technologies for disposal. Refer to “Contacting Agilent” on page 12 for assistance.
Agilent for repair. If you wish to send your instrument to Agilent Technologies for service or repair: • Include a complete description of the service requested or of the failure and a description of any failed test and any error message.