MANUFACTURER - FILE THE CLAIM WITH THE RETAILER. If the unit was shipped or has been laying on its back for any period of time allow the refrigerator to sit upright for a period of at least 24 hours before plugging in. This will assure oil returns to the compressor.
For this reason it is important this area to not be obstructed and be kept clean. Marvel does not rec- ommend the use of custom made grilles as air flow may be restricted because of inadequate openings.
• Temperature Sensor Fault: If the controller sensor alarm will sound. “E1” will flash on the display, and an alarm will sound. Please call Marvel Customer Service or your dealer if this error code is displayed. • Condenser Needs Cleaning: cessitate cleaning the air flow, “cL”...
20 seconds every 60 minutes. Turning Refrigerator Off To turn refrigerator off, press and hold “ON/OFF” button for three (3) seconds. “OFF” will appear on the display Additional MicroSentry™...
DIMENSIONS FOR MODELS 30ARM WITH OVERLAY DOOR Recommended Rough in Opening Dimensions, Model 30ARM Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet 14-7/8” (37.78 cm) 34-1/4” to 34-1/2” (87 to 87.6 cm) 3” to 3-1/4” 7.62 to 8.26cm) depth 15”...
DIMENSIONS FOR MODEL 61ARM WITH OVERLAY DOOR Recommended Rough in Opening Dimensions, Model 61ARM Overlay Door 34-1/2” (87.6 cm) *24” (61 cm) standard cabinet 24” (61 cm) (119.38 cm) 23-7/8” (60.66 cm) 34-1/4” to 34-1/2” (87 to 87.6 cm) 3” to 3-1/4” 7.62 to 8.26cm) depth 47”...
25-11/16” (65.28 cm) 23-7/8” (60.66 cm) 31-5/8” to 31-7/8” (80.31 to 80.98 cm) 3” to 3-1/4” 7.62 to 8.26cm) Recommended Rough In Opening Dimensions, Model 6ADAM 32-1/2” (82.6 cm) *24” (61 cm) standard cabinet depth 24” (61 cm) DIMENSIONS FOR MODEL 6ADAM 47”...
DIMENSIONS FOR MODEL 6ADAM WITH OVERLAY DOOR Recommended Rough In Opening Dimensions, Model 6ADAM Overlay Door 32-1/2” (82.6 cm) *24” (61 cm) standard cabinet 24” (61 cm) 23-7/8” (60.66 cm) 31-5/8” to 31-7/8” (80.31 to 80.98 cm) 3” to 3-1/4” 7.62 to 8.26cm) depth 47”...
Step 1: Verify door alignment The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side.
Page 14
3/32” (2.4mm) Diameter. Pilot Hole Softwood 5/64 (2.0mm) Diameter. Pilot Hole Table B If your refrigerator has a door lock proceed to Step 7. If your refrigerator does not have a door lock proceed to Step 9. Step 7: Mark and drill lock hole.
Page 15
Install the top hinge pin so the screw head is flush with the top surface of the hinge. If applicable insert key into lock and verify the lock cam works properly with the catch bracket on the front of the refrigerator cabinet. Top hinge pin Top door hinge...
CARE AND CLEANING Condenser Air Flow The machine compartment located beneath the cabinet does not require frequent cleaning; however, satisfactory performance depends on adequate ventilation. Be sure nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush or vacuum lint and dirt from the front grille openings.
If Service is Required: • If the product is within the first year warranty period please call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. •...
Entire Product Limited One Year Parts and Labor Warranty Marvel warrants that it will supply all necessary parts and labor to repair or replace in the end user’s home or office, any component which proves to be defective in material...
The data can be cleared by pressing “SET” and “ON/OFF” simul- taneously while the value is displayed. NOTE: It is normal for refrigerator temperature to fluctuate from set point by several degrees. Minimum Stored Temperature (tLO): Mini-...
Page 20
Northland-Marvel P .O. Box 400 1260 E. Van Deinse St. Greenville MI 48838 800.223.3900 41011753-EN Rev G 11/10/09 www.marvelrefrigeration.com All specifications and product designs subject to change without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for...
Need help?
Do you have a question about the 30ARM-BB-F and is the answer not in the manual?
Questions and answers