Advertisement
* Detail EDID Options are below
ⓐ Product ID
Model Name
HEX
**SL9****
0001
0000
ⓑ Serial No: Controlled on production line.
ⓒ Month, Year: Controlled on production line:
ex) Monthly : '02' -> '02'
Year : '2009' -> '13'
ⓓ Model Name(Hex):
MODEL
47SL9000 00 00 00 FC 00 34 37 53 4C 39 30 30 30 2D 5A 41 0A 20
47SL9500 00 00 00 FC 00 34 37 53 4C 39 30 30 30 2D 5A 42 0A 20
ⓔ Checksum: Changeable by total EDID data.
ⓕ Vendor Specific(HDMI)
INPUT
HDMI1
HDMI2
HDMI3
HDMI4
4.5. Checking the function of Bluetooth
using adjusts Remote control
(1) Auto checking
- Auto checking is doing in "Power Only".
- Checking the result of searched(check that is in list or not).
- Go out of checking mode pushing button "Exit".
(2) Manual checking
- Push the button "Power Only" and "Exit".
- Push the button hot key "Bluetooth".
- Checking the result of searched(check that is in list or not).
- Go out of checking mode pushing button "Exit".
4.6. Outgoing condition Configuration
- When pressing "IN-STOP" key by Service remote control,
Red LED are blinked alternatively. And then Automatically
turn off. (Must not AC power OFF during blinking)
4.7. Internal pressure
Confirm whether is normal or not when between power
board's ac block and GND is impacted on 1.5kV(dc) or
2.2kV(dc) for one second.
Copyright ©2009 LG Electronics. Inc. All right reserved.
Only for training and service purposes
EDID Table
DDC Function
0100
0100
MODEL NAME(HEX)
MODEL NAME(HEX)
67 03 0C 00 10 00 B8 2D
67 03 0C 00 20 00 B8 2D
67 03 0C 00 30 00 B8 2D
67 03 0C 00 40 00 B8 2D
5. Serial number D/L
• Press "Power on" key of service remote control.
(Baud rate : 115200 bps)
• Connect RS232 Signal Cable to RS-232 Jack.
Analog
• Write Serial number by use RS-232.
Digital
• Must check the serial number at the Diagnostics of SET UP
menu. (Refer to below).
5.1. Signal TABLE
CMD
CMD : A0h
LENGTH : 85~94h (1~16 bytes)
ADH : EEPROM Sub Address high (00~1F)
ADL : EEPROM Sub Address low (00~FF)
Data : Write data
CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n
Delay : 20ms
5.2. Command Set
No.
1
* Description
FOS Default write : <7mode data> write
Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,
Phase
Data write : Model Name and Serial Number write in EEPROM.
5.3. Method & notice
A. Serial number D/L is using of scan equipment.
B. Setting of scan equipment operated by Manufacturing
Technology Group.
C. Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0.
- 13 -
LENGTH
ADH
ADL
DATA_1
Adjust mode
CMD(hex)
LENGTH(hex)
EEPROM WRITE
A0h
84h+n
. . .
Data_n
CS
DELAY
Description
n-bytes Write (n = 1~16)
LGE Internal Use Only
Advertisement
