Table of Contents
Advertisement
CORDLESS DIGGING TOOL SAFETY WARNINGS
WARNING! Maintain a firm grip on the handles with both
hands while using the auger. Keep the auger bit away from
the body and below waist level.
■
Replace the auger if it is cracked, bent, or damaged in
any way. Ensure that the auger is properly installed and
securely fastened. Failure to do so can cause serious
injury.
■
Make sure that the handles are properly and securely
attached.
■
Consider the environment in which you are working.
Keep the working area free from electric cables or
underground utilities.
■
Use only the manufacturer's replacement parts. Do not
use any other attachment.
■
Replace the auger bit immediately if there are any
cracks or any damage.
■
Do not touch the auger bit when the product is turned on.
■
If the auger bit jams, turn off the product immediately.
■
Maintain a firm grip on both handles during operation.
■
Do not use the product with the handle above waist level
to avoid serious chest injuries when the product hits a
hard object.
■
Always keep the handles dry and clean.
■
Ensure that all handles are properly fitted and in good
condition.
■
Do not start operating the product until you have a clear
work area and secure footing.
■
Do not modify the product in any way or use it to power
any attachments or devices that are not recommended
by the manufacturer.
■
Before starting the product, ensure that the bit is not
contacting any object.
■
Do not use the product when there is a possibility of
thunderstorm or lightning. Store the product safely
indoors.
■
To reduce the risk of injury associated with contacting
moving parts, always turn off the product, remove the
battery pack, and allow both to cool down. Make sure
that all moving parts have come to a complete stop:
●
before servicing
●
before clearing a blockage
●
before checking, cleaning, and working on the
product
●
before changing accessories
●
after striking a foreign object
●
whenever leaving the product unattended
●
whenever performing maintenance
●
whenever the product starts to vibrate abnormally
■
Immediately turn off the product and remove the battery
pack in the event of an accident or breakdown. Do not
operate the product again until it has been fully checked
by an authorised service centre.
■
Brace the product properly before use. The product
produces a high output torque and without properly
bracing the tool during operation, loss of control may
occur resulting in personal injury.
4
Original Instructions
■
Hold the product by the insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
■
Always start drilling at a low speed and with the auger
tip in contact with the workpiece. At higher speeds, the
auger is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Never operate the product at higher speed than the
maximum speed rating of the auger bit.
■
Apply pressure only in direct line with the auger and do
not apply excessive pressure. Augers can bend causing
breakage or loss of control, resulting in personal injury.
■
To avoid personal injury, do not start the product when
the auger bit is not in contact with the ground.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the product,
battery pack, or charger in fluid or allow fluid to flow inside
them. Corrosive or conductive fluids, such as seawater,
certain industrial chemical, and bleach or bleach-containing
products, etc., can cause a short circuit.
LED DISPLAY
Setting
Green LED light
Running
Kickback:
deactivated
Issue
Blue LED light
Kickback event
Overload
ACTIVE KICKBACK AND OVERLOAD DISPLAY
The kickback feature is active when the dotted blue lights
are on. When the product detects tough soil or debris, the
feature is activated to protect the user. When the product
stops, release the trigger and then remove the product from
the hole.
The overload function is activated when the red bar light is
highlighted. When the product stops, release the trigger and
then remove the product from the hole.
SWITCH POSITION
Display
Description
REV
Reverse
1
Speed 1
2
Speed 2
NOTE: Turning off the kickback protection at any time is not
recommended. However, in the event that it is deactivated,
the product still has overload protection.
Red LED light
On
Off
On
On
Red LED light
On
Off
Off
On
Location
Bottom
Middle
Top
Advertisement
Table of Contents
