Pioneer SE-MS9BN - ANC Headphones Quick Start Guide

Pioneer SE-MS9BN - ANC Headphones Quick Start Guide

Also See for SE-MS9BN:

Advertisement

Pioneer SE-MS9BN - ANC Headphones Quick Start Guide

Before you start

This document describes the information and operations required for startup. For more advanced operating procedures, read the instruction manual which is available on the website.

<Europe>
http://www.hkpioneer.net/en/download.php
<U.S.A and Canada>
http://help.pioneerhomeusa.com


Download the Pioneer Headphones APP for setup.
www.apple.com
play.google.com

Set Contents

Confirm the presence of all parts and components before use.

  1. Headphones
  2. Micro-USB cable
  3. Headphone cord
  4. Carrying pouch
  5. Warranty (U.S.A. and Canada / Japan)
  6. Quick Start Guide (this document)
  7. Safety Guide

Names of Parts

(see Fig. 2)
Names of Parts

  1. N-mark
  2. ( + ) button
  3. Play / Pause button
  4. ( – ) button
  5. LED indicator
  6. () button
  7. Assistant button
  8. Micro-USB port
  9. Headphone jack
  10. Microphone

Charging the batteries

 Charging the batteries
The unit's battery must be recharged before use.
The accessory micro-USB cable must be used for recharging the unit's battery.
Connect the appropriate connector on the accessory micro-USB cable to the microUSB port on the headphones, and the USB plug on the other end to a USB port on a computer (see Fig. 3).

  • When recharging begins, the LED indicator on the headphones will light red.
  • Full recharging requires about 4 hours; when recharging is completed, the LED indicator will turn off.

Note

  • Battery recharging time and usable battery time may vary depending on ambient temperature and frequency of use.

Notes on battery charging

  • Battery performance is influenced by the surrounding temperature. Charge the supplied rechargeable batteries within a temperature range of 10 to 35 degrees celcius.
  • Batteries become slightly warm when charging. This is not a malfunction.
  • Recharging may not be possible if computer is in power-saving mode.
  • This device cannot be used during charging.

Pairing

Pairing must be performed before the headphones can be used to listen to music or communicate using a Bluetooth device.
For further details regarding the pairing procedure, consult the user's manual for your Bluetooth device.

  1. While the power of the unit is off, hold down the ( ) button until the unit enters pairing mode.
  • The pairing mode is confirmed by the LED indicator's alternately flashing blue and red.
    Release the ( ) button after confirming that the LED indicator is alternately lighting blue and red.
  1. Turn on the power to the Bluetooth device you wish to pair with, and begin pairing; search for this unit (wireless headphones) from the paired Bluetooth device.
  • Set the Bluetooth device close (within one meter) to the wireless headphones.
  • These wireless headphones will appear in the Bluetooth device's display as "SE-MS9BN".
  1. Confirm that pairing has been successfully completed with the Bluetooth device.
  • Look at the display for the Bluetooth-enabled device and select "SE-MS9BN".
  • When the LED lamp is flashing in blue slowly about once every 3 seconds, pairing is complete. When it is flashing quickly about once every second, pairing is not complete.
  • The PIN code for these wireless headphones has been factory set at "0000".
    Input this code if requested by the Bluetooth device.

Connect to the Bluetooth device

  • Confirm that the power to the wireless headphones is ON before connecting to the Bluetooth device.
  • Depending on the device, connection between the wireless headphones and Bluetooth device may be effected automatically after pairing.

Disconnecting from the Bluetooth device

  • Hold down the () button until the flashing LED lamp turns off and the power of the device turns off.

Using NFC for pairing

 Using NFC for pairing
When a smart phone or tablet device is equipped with NFC, Bluetooth pairing (and depairing) can be performed simply by merely swiping the device over the headphones.

  • Depending on the smart phone or tablet device used, the NFC signal reception may be too weak to perform one-touch connections. The unit may pair with a device other than the desired one if multiple NFC devices are nearby. In that case, follow the manual pairing procedure outlined in step 4.

How to set pairing

  1. Hold the () button depressed while the unit's power is turned off to enter the pairing mode.
  2. Swipe the "N-mark" on the device to be connected about 1 cm above the "N-mark" on the left side of the headband. (see Fig.4)
  3. The device will automatically begin setting the pairing.
    When the LED lamp is flashing in blue slowly about once every 3 seconds, pairing is complete. When it is flashing quickly about once every second, pairing is not complete.

* Only one device can be connected at a time.

Disconnecting
With connecting to this unit, swipe the "N" mark on the device to be connected about 1 cm above the "N-mark" on the left side of the headband.
The connection will be automatically undone.
Depending on the specifications of the connected Bluetooth device, the connection cannot be terminated from the NFC device. In that case, perform the procedure of "Disconnecting from the Bluetooth device" in "4. Pairing".

Specifications

Transmission format: Bluetooth Standard Protocol Ver. 4.2
Output: Bluetooth Standard Protocol Power Class 2
Maximum transmission distance: .About 10 m line of sight *1
Frequency used: 2.4 GHz (2.4000 GHz to 2.4835 GHz)*2
Modulation: FHSS
Supported Bluetooth profiles: A2DP, AVRCP, HFP, HSP
Supported CODEC: SBC, AAC, Qualcomm® aptXTM audio, Qualcomm® aptXTM HD audio
Contents protection: SCMS-T
Battery life with continuous use: Maximum 24 hours of continuous transmission
(NC ON/including music-play time)
Maximum 27 hours of continuous transmission
(NC OFF/including music-play time)
Recharging time: About 4 hours
Rating input: 5 V 200 mA or 3.7 V 545 mAh
Battery Power: DC 3.7 V internally rechargeable lithium-ion battery
Weight: 300 g

HEADPHONES
Type: Fully-enclosed dynamic headphones
Driver units: ø40 mm
Frequency response: 5 Hz to 22 000 Hz (With Bluetooth connection)
5 Hz to 40 000 Hz (With wired connection)
Maximum input power: 1 000 mW (With wired connection)
Impedance: 32 Ω (With wired connection)
Sensitivity: 100 dB (With wired connection)
Ear pad: Polyurethane (leather finish)

MICROPHONE
Type: MEMS
Directionality: Omni-directional microphone
Frequency response: 100 Hz to 8 000 Hz

ACCESSORIES
Micro-USB cable: 1
Headphone cord: 1
Carrying pouch: 1
Warranty (U.S.A. and Canada / Japan): 1
Quick Start Guide (this document): 1
Safety Guide: 1

*1 Transmission distance is an approximation. Actual usable distance may vary depending on surrounding conditions.
*2 This product utilizes radio waves in the 2.4 GHz spectrum. Some signal dropouts may be experienced due to interference with radios, microwave ovens, and other devices using the 2.4 GHz spectrum.

Note
Specifications and design are subject to possible modifications without notice due to improvements.

© 2018 Onkyo & Pioneer Innovations. All rights reserved.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Pioneer SE-MS9BN - ANC Headphones Quick Start Guide

Advertisement

Table of Contents