Related Manuals for Inova inovabed Sofa-WallBed
Summary of Contents for Inova inovabed Sofa-WallBed
- Page 1 Sofa-WallBed | Assembly Manual Inova LLC 2 Van Buren Blvd. Guilderland Center, NY 1208585...
- Page 2 Sofa-WallBed...
- Page 3 Quick Start Guide Sofa-WallBed | Assembly Manual...
-
Page 4: Helpful Information
Quick Start Guide HELPFUL INFORMATION • Prior to opening your shipment,check and • All Cabinetry and Sofa parts are labeled for easy confirm the room is completely ready to identification receive the furniture (see “Room Readiness Checklist” on next page). •... - Page 5 Quick Start Guide ROOM READINESS • Clear out any items in the room so you have a TIP: Depending on your unit, you may want to clear path to the wall and an open area to remove existing baseboard that is located on the CHECKLIST assemble the Bed wall where the Bed will be installed.
-
Page 6: Tools Needed
Quick Start Guide H-115 Euro Screw, 18mm TOOLS NEEDED: HARDWARE LIST: H-491 Machine Screw, 3/4” Electric Power Drill Bolts: Nuts: #2 Phillips Bit (provided) H-068 Panel Bolts, 2” H-086 Flange Nuts, 5/16” #3 Phillips Bit (provided) H-112 Flange Head Bolts, 5/16” x 2” H-767 Nylock Nuts, 5/6”... -
Page 7: How It Works
How It Works Sofa-WallBed | Assembly Manual... - Page 8 How It Works HOW IT MOVES UP TO LOWER THE SOFA-WALLBED: Handles are located on the outside of the AND DOWN: Bed Cabinet (on the Bed Platform) to open The mechanisms that allow the Sofa- and lower the Bed Platform. WallBed to move up and down are spring- TO RAISE THE SOFA-WALLBED: loaded and located on the inside face of each...
- Page 10 How It Works HOW TO STEPS FOR ADJUSTMENT: ADJUST TENSION: To adjust the number of springs,you will need to temporarily “walk” the cabinet and sofa forward until it is around two feet from the wall. Do not To adjust the tension of the Sofa-WallBed: move the unit by grabbing the sofa arms as it may damage it.
-
Page 11: Troubleshooting
Troubleshooting Sofa-WallBed | Assembly Manual... - Page 12 TO LOWER THE HEADBOARD: obstructions. If there is no obvious culprit,call If any of the hinges or other parts of the Inova customer service for assistance in mechanism on Sofa-WallBed creak, spray Simply pull the upper lip of the Headboard away troubleshooting the issue.
- Page 13 TROUBLESHOOTING (CONT.) I HAVE A BROKEN PART THAT HOW DO I RETRIEVE SOMETHING the top of the seat deck back. Once the seat deck is underneath the Back Cushions, you’ll NEEDS TO BE REPLACED THAT FELL UNDERNEATH THE SEAT need to reset the Rear Support mechanisms DECK?: by cycling the Bed open and closed once.
- Page 14 Sofa-WallBed: Hardware Overview The illustrations drawn are general representations of your products hardware H-016 H-019 H-068 H-231a H-120 H-107 H-162 H-508 H-087 H-738 H-231b H-783 H-086 H-417 H-085 H-115 H-491 H-073 H-233 H-062 H-244 H-493 H-934 H-065 H-285a H-067 H-003 H-285b H-235 H-011...
- Page 15 Step 1: Prepare the Right Pier The illustrations drawn are general representations of your product’s parts and hardware A. Lay the Right Pier on the floor as shown (padding or carpet is suggested to be underneath the pier to avoid scratching). B.
- Page 16 Step 2: Prepare the Cabinet Back and Cabinet Top The illustrations drawn are general representations of your product’s parts and hardware A. Attach the Shelf to the Cabinet Back using the provided H-065 panel screws and 4mm hex driver. B. Attach the Valance to the Cab Top/Sub Top assembly using the provided H-065 panel screws and insert the H-003 dowels into both ends of the sub top. Shelf H-065 Enlarged view...
- Page 17 Step 3: Cabinet Back and Cabinet Top to Right Pier The illustrations drawn are general representations of your product’s parts and hardware A. Lay the Right Pier on its side if it is not already (padding or carpet is suggested to be underneath the pier to avoid scratching). B.
- Page 18 Step 4: Prepare The Left Pier The illustrations drawn are general representations of your product’s parts and hardware A. Lay the Left Pier on the floor as shown (padding or carpet is suggested to be underneath the pier to avoid scratching). B.
-
Page 19: Two Person Lift
TWO PERSON LIFT! Step 5: Assemble The Bed Cabinet The illustrations drawn are general representations of your product’s parts and hardware No hardware is needed for this step. With another person, lift and flip the Left Pier with one person at the top end and the other at the bottom end. ( the hardware previously installed is facing toward the floor now ). - Page 20 Step 6: Assemble The Base Plate The illustrations drawn are general representations of your product’s parts and hardware A. Attach the Rear Ramps to the Left and Right Base Pads using the H-065 panel screws provided. ( Important: MUST be fully tightened so that the Rear Ramps butt up to the Base Pads). B.
- Page 21 TWO PERSON LIFT! Step 7: Attach the Base Pad to the Bed Cabinet The illustrations drawn are general representations of your product’s parts and hardware A. Place the assembled Base Pad on the ground (close to the area where you want the bed to be once completed but away from the wall). B.
- Page 22 Step 8: Attach the Arms The illustrations drawn are general representations of your product’s parts and hardware A. Place the Left and Right Arms as shown on the Base Pad B. Align the holes in the back of the Arm and the front of the Pier then bolt them together using the H-068 panel bolts. Complete this step on both Arms. C.
- Page 23 Step 9: Install the Headboard The illustrations drawn are general representations of your product’s parts and hardware A. Screw the H-231b button fix connectors to the Shelf as shown using the H-115 euro screws provided. B. Attach the H-231a 90 degree snap connectors to the Headboard as shown using H-087 screws. C.
- Page 25 Anti-Tip Strap Attachment The illustrations drawn are general representations of your product’s parts and hardware A. Move the Bed Cabinet against the wall into its final position in the room if not already done so. B. Locate the Studs in the wall. Attach the H-508 cable and bracket assembly to the studs, just above the Bed Cabinet top using H-016 drywall screws. C.
- Page 27 Step 10: Install the Mechanisms The illustrations drawn are general representations of your product’s parts and hardware A. Attach the Left Mechanism to the Left Pier as shown using the H-417 low head cap screws provided HAND TIGHTEN to start all low head cap screws. DO NOT fully tighten the screw at the top/front corner of the mechanism and use the H-067 washer with this bolt.
- Page 28 Step 11: Head Rail, Foot Rail and Side Rails The illustrations drawn are general representations of your product’s parts and hardware A. Attach the M-19 head/foot angle brackets to the Head Rail and Foot Rail using the H-073 euro screws provided and the H-933 pozi drive bit. Then, attach the M-224 side angles to the Left and Right Side Rails using the remaining H-073 euro screws.
- Page 29 Step 12: Assemble Bed Platform The illustrations drawn are general representations of your product’s parts and hardware A. Place the Left and Right Bed Panels on the ground with the hardware facing up (padding or carpet is suggested to be underneath the Bed Panels to avoid scratching). B.
- Page 30 TWO PERSON LIFT! Step 13: Mechanize The Bed Platform The illustrations drawn are general representations of your product’s parts and hardware A. Insert the H-738 bolts into hole #1 on the Left and Right Side Rails. Then attach the H-086 nuts to the ends of bolts, but DO NOT fully tighten. Insert the H-739 low head cap screw into hole #3 on the Left and Right Side Rails.
- Page 31 TWO PERSON LIFT! Step 14: Install the Bed Platform The illustrations drawn are general representations of your product’s parts and hardware A. Lift the Bed Platform assembly as shown, then align the bolts in hole one on both Side Rails with the slot on both Spring Mechanisms as shown. TIP: For the easiest installation, walk the Bed Platform into the bed Cabinet slowly keeping the sides of the Bed Platform parallel to the Sofa Arms.
- Page 32 Step 15: Attach the Back Cushions The illustrations drawn are general representations of your product’s parts and hardware A. Attach the Back Cushion to the Bed Platform using H-491 machine screws, starting with the second hole from the bottom of the slide aligning with the bottom hole on the Bed Panel. Ensure 3 machine screws per slide are utilized.
- Page 33 Step 16: Install the Seat Deck The illustrations drawn are general representations of your product’s parts and hardware A. Remove the seat cushions from the Seat Deck, then angle the Seat Deck Front Slider to be under the ledge of both arms as shown. B.
- Page 34 Step 17: Attach the Skirt The illustrations drawn are general representations of your product’s parts and hardware A. Engage the rear supports and prepare to attach the Skirt by opening the Bed to a 45 degree angle. You will hear a slight knocking sound- that is the rear supports engaging. B.
- Page 35 Step 18: Secure Mechanism Covers The illustrations drawn are general representations of your product’s parts and hardware A. Open the Bed fully and place the Left Mechanism Cover over the Left Mechanism and the Right Mechanism Cover for the Right Mechanism. B.
- Page 36 Step 19: Seat Cushions and Mattress The illustrations drawn are general representations of your product’s parts and hardware A. Put the Seat Cushions on the seat deck, make sure they are facing Velcro to Velcro B. Open the bed and place the mattress on the Bed Platform, cycle the bed open and closed a few times to ensure everything is functioning smoothly. If it is not, refer back to the trouble shooting section at the beginning of the assembly manual C.
- Page 37 C O N G R A T U L A T I O N S ! Y O U R S O F A - W A L L B E D I S R E A D Y F O R Y O U T O E N J O Y ! B E F O R E Y O U G O .