Summary of Contents for HIKVISION DS-KH6320-LE1/White
Page 1
Network Indoor Station Configuration Guide...
Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
Network Indoor Station Configuration Guide CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY...
Page 4
Network Indoor Station Configuration Guide Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or Danger could result in death or serious injury. Indicates a potentially hazardous situation which, if not Caution avoided, could result in equipment damage, data loss,...
Page 5
Network Indoor Station Configuration Guide Safety Instruction Warning All the electronic operation should be strictly compliance with the electrical safety ● regulations, fire prevention regulations and other related regulations in your local region. Please use the power adapter, which is provided by normal company. The power ●...
Page 6
Network Indoor Station Configuration Guide Please use the provided glove when open up the device cover, avoid direct contact ● with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. Please use a soft and dry cloth when clean inside and outside surfaces of the ●...
Page 7
Network Indoor Station Configuration Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 8
Network Indoor Station Configuration Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/ 65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the...
Page 9
Network Indoor Station Configuration Guide l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
Network Indoor Station Configuration Guide Contents 1 About this Manual ..................1 2 Local Operation ..................2 2.1 Activate Indoor Station ..................2 2.2 Quick Operation ....................2 2.3 Basic Settings ....................5 2.3.1 Set Indoor Station Network Parameters ........... 5 2.3.2 Set Linked Device IP ..................
Page 11
Network Indoor Station Configuration Guide 3.4 Remote Configuration ..................21 3.4.1 System ....................21 3.4.2 Video Intercom ..................26 3.4.3 Network ....................31 3.5 Person Management ..................34 3.5.1 Organization Management ..............35 3.5.2 Person Management ................36 A. Communication Matrix and Device Command ........40...
Network Indoor Station Configuration Guide 1 About this Manual Get the manual and related software from or the official website (http:// www.hikvision.com). Product Model DS-KH6320-LE1/DS-KH6320-LSE1/DS- Network Indoor Station KH6220-LE1...
Network Indoor Station Configuration Guide 2 Local Operation 2.1 Activate Indoor Station You can only configure and operate the indoor station after creating a password for the device activation. Steps 1. Power on the device. It will enter the activation page automatically. Figure 2-1 Activation Page 2.
Page 14
Network Indoor Station Configuration Guide Steps 1. Choose Language and tap Next. 2. Set network parameters and tap Next - Edit IP Address, Subnet Mask and Gateway. - Enable DHCP, the device will get network parameters automatically. Figure 2-3 Network Parameters 3.
Page 15
Network Indoor Station Configuration Guide Figure 2-4 Indoor Station Settings - Select Indoor Extension, and set the No. Tap Next, and set the linked indoor station. Note If the indoor extension and the indoor station are in the same LAN, the indoor station will be displayed in the list.
Network Indoor Station Configuration Guide Figure 2-6 Related Device 1) Set the linked device's parameters. Note If the device is inactive, the system will pop up the dialog to activate the device. 2) Tap to pop up the Network Settings page. 3) Edit the network parameters of the door station manually or enable DHCP to get the network parameters automatically.
Network Indoor Station Configuration Guide Steps Note The default IP address of the indoor station is 192.0.0.64. Two ways are available for you to set IP address: DHCP, and set IP address manually. 1. Tap Settings → → to enter the network settings page. Note Enter activate password as the admin password.
Network Indoor Station Configuration Guide Steps Note Here take door station network settings as example. 1. Tap Settings → → to enter the device management page. Note Default admin password is the activation password. Figure 2-8 Device Management 2. Tap Main Door Station to pop up the device information dialog. 1) Tap to switch the device type.
Network Indoor Station Configuration Guide Note Default admin password is the activation password. Figure 2-9 Set Indoor Station No. 2. Configure the indoor station and indoor extension informations. - Select Indoor Station as Indoor Station Type. Edit the Room No. and Floor No. - Select Indoor Extension as Indoor Station Type.
Page 20
Network Indoor Station Configuration Guide Zone Settings You can set the zone type, alarm type and delay time and other parameters of 8 zones. Before You Start Tap Settings → → Preference to enable Alarm function. Steps Note Arming status page and zone settings page are hidden by default. You should enable alarm function first.
Page 21
Network Indoor Station Configuration Guide Set the alarm type as delay alarm, and you should set the entering delay duration and exiting delay duration. Both the entering delay duration and the exiting delay duration are from 30s to ● 60s. For Gas Detector and Smoke Detector, the alarm type is set as default 24h ●...
Network Indoor Station Configuration Guide Note Zones are configurable on the arming mode page. ● 24H alarm zone including smoke detector zone and gas detector zone will be ● triggered even if they are disabled. Arming mode settings should be configured with the settings of arming status ●...
Network Indoor Station Configuration Guide Arm or disarm the zone for the indoor station by entering the arm/disarm password. Note Arm/Disarm settings page is hidden by default. Tap Settings → → Preference to enable Alarm function, you can edit the alarm parameters. Duress Code When you are hijacked and forced to open the door, you can enter the duress code.
Network Indoor Station Configuration Guide Figure 2-13 Synchronize Time 3. Enable NTP. 4. Enter Sync Interval, IP Addr/Domain, and Port No. Note The default unit of synchronizing interval is minute. 5. Select Time Zone. 2.6 Sound Settings You can set the ringtone, ring duration, volume of microphone and loudspeaker, enable/disable touch sound, and auto-answer on call settings page.
Network Indoor Station Configuration Guide Figure 2-14 Call Settings 2. Set corresponding parameters. Ringtone There are 3 ringtones by default, and you can custom and import at most 4 ringtones via Batch Configuration Tool or iVMS-4200 Client Software. Ringtone Duration: The maximum duration of indoor station when it is called without being accepted.
Network Indoor Station Configuration Guide Figure 2-15 Restore Settings 3. Restore the indoor station. You can choose from restore default settings or restore all settings. - Tap Restore Default Settings to restore the default settings and reboot the system. - Tap Restore All to restore all settings to factory parameters and reboot the system.
Network Indoor Station Configuration Guide Clean Screen Enable the clean screen function and the screen will be locked for 30 s. In the time duration, you can clean the screen surface. Hold the disable icon or wait for 30 s to end the status. Language Tap Settings →...
Network Indoor Station Configuration Guide 3 Remote Operation via the Client Software The Video Intercom module provides remote control and configuration on video intercom products via the iVMS-4200 client software. 3.1 Activate Device Remotely You can only configure and operate the indoor station after creating a password for the device activation.
Network Indoor Station Configuration Guide After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 3.2.1 Add Video Intercom Devices Steps Note You can add at most 512 indoor stations and main stations in total to the client, ●...
Page 30
Network Indoor Station Configuration Guide Figure 3-1 Add the Device 4. Optional: Click Online Device, the active online devices in the same local subnet with the client software will be displayed on the Online Device area. Note To add online devices to the software, you are required to change the device IP address to the same subnet with your computer first.
Network Indoor Station Configuration Guide Edit a name for the device as you want. Address Input the device's IP address. The IP address of the device is obtained automatically in this adding mode. Port Input the device port No. The default value is 8000. User Name Input the device user name.
Network Indoor Station Configuration Guide 3.3 System Configuration You can configure the video intercom parameters accordingly. Steps 1. Click Maintenance and Management → System Configuration → Acs and videoIntercom to enter the system configuration page. 2. Enter the required information. Ringtone Click ...
Page 33
Network Indoor Station Configuration Guide Device Information Click Device Information to enter device basic information page. You can view basic information (the device type, and serial No.), and version information of the device. Figure 3-2 Device Information General Click General to enter device general parameters settings page. You can view and edit the device name and device ID.
Page 34
Network Indoor Station Configuration Guide Figure 3-4 Synchronize Time Select Time Zone or Enable NTP. Click Save to save the time settings. Time Zone ● Select a time zone from the drop-down list menu. ○ Click Synchronization. ○ ● Check the checkbox of Enable NTP to enable NTP. ○...
Page 35
Network Indoor Station Configuration Guide Figure 3-5 System Maintenance Click Reboot and the system reboot dialog box pops up. Click Yes to ● reboot the system. Click Restore Default Settings to restore the default parameters. ● Click Restore All to restore all parameters of device and reset the device ●...
Page 36
Network Indoor Station Configuration Guide Click ... to select the upgrade file and click Upgrade to remote upgrade ● the device. The process of remote upgrade will be displayed in the process bar. Select a language, and click Save to change the device system language. ●...
Network Indoor Station Configuration Guide Note The new password and confirm password should be identical. ● After editing the password of device, click refresh button from the device ● list, the added device will not be there. You should add the device again with new password to operate the remote configuration.
Page 38
Network Indoor Station Configuration Guide Figure 3-8 Time Parameters 2. Configure the maximum ring duration, maximum live view time, and call forwarding time. 3. Click Save. Note Maximum ring duration is the maximum duration of indoor station when it is ●...
Page 39
Network Indoor Station Configuration Guide For indoor station, you can change the admin password, arm/disarm password, unlock password and duress code. For indoor extension, only admin password and arm/disarm password need to be configured. Zone Alarm Steps 1. Click Zone Alarm to enter the zone settings page. Figure 3-10 Zone Alarm 2.
Page 40
Network Indoor Station Configuration Guide When the zone type is set to be Instant Alarm, only under arming mode, the ● indoor station will receive alarm message when the detector is triggered. Under disarming mode, it will not receive alarm message when the detector is triggered.
Page 41
Network Indoor Station Configuration Guide Note Indoor extension does not support this function. Export and Import Added Device Information Steps 1. Click Export to export the added device information file. 2. Edit parameters of added devices in batch in the exported file. 3.
Network Indoor Station Configuration Guide Figure 3-13 Volume Input and Output 2. Slide the slider to adjust the volume input, volume output and talk volume. 3. Click Save to enable the settings. Deploy Info Click Deploy Info, you can get the deploy informations. Figure 3-14 Deploy Info 3.4.3 Network Local Network Configuration...
Page 43
Network Indoor Station Configuration Guide Figure 3-15 Local Network Configuration 2. Enter the local IP address, subnet mask, gateway address, and port No. 3. Click Save to enable the settings. Note The default port No. is 8000. ● After editing the local network parameters of device, you should add the ●...
Page 44
Network Indoor Station Configuration Guide Note After adding main station IP Address, the linkage between indoor station and ● main station can be realized. After adding the door station IP Address, the video intercom between indoor ● stations of same building can be realized. After adding SIP Server Address IP, the video intercom of same community: ●...
Network Indoor Station Configuration Guide 3. Set the Community No., Building No., Unit No., Floor No. and Room No. 4. Enter the main station IP address, (main) door station IP address, SIP server IP address, management center IP address, and doorphone IP address. 5.
Network Indoor Station Configuration Guide Figure 3-17 Personal Management Application The page is divided into two parts: Organization Management and Person Management. Organization Management You can add, edit, or delete the organization as desired. Person Management After adding the organization, you can add the person to the organization and issue card to persons for further management.
Network Indoor Station Configuration Guide 2) Then the added organization will be the sub-organization of the upper-level organization. Note Up to 10 levels of organizations can be created. Modify and Delete Organization You can select the added organization and click to modify its name.
Page 48
Network Indoor Station Configuration Guide 1) Enter basic information: name, tel, birthday details, effective period and email address. 2) Optional: Click Add Face to upload the photo. Note The picture should be in *.jpg format. Click Upload Select the person picture from the local PC to upload it to the client.
Page 49
Network Indoor Station Configuration Guide 3) Check the checkboxes to select the person information to export. 4) Click OK to start exporting. 2. Importing Person: You can import the Excel file with persons information in batch from the local PC. 1) Click Import Person.
Page 50
Network Indoor Station Configuration Guide Select the person and click Edit to open the editing person dialog. To delete the person, select a person and click Delete to delete it. Note If a card is issued to the current person, the linkage will be invalid after the person is deleted.
A. Communication Matrix and Device Command Communication Matrix Scan the following QR code to get the device communication matrix. Note that the matrix contains all communication ports of Hikvision access control and video intercom devices. Figure A-1 QR Code of Communication Matrix Device Command Scan the following QR code to get the device common serial port commands.
Need help?
Do you have a question about the DS-KH6320-LE1/White and is the answer not in the manual?
Questions and answers