Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ETAS ETAI12
Summary of Contents for ETAS ETAI12
- Page 1 ETAI12 ETK ECU Flex Adapter, Erni - Samtec (12fc - 10fc), 0m136 User Guide...
- Page 2 The data in this document may not be altered or amended without special notification from ETAS GmbH. ETAS GmbH undertakes no further obligation in relation to this docu- ment. The software described in it can only be used if the customer is in possession of a general license agreement or single license.
-
Page 3: Table Of Contents
Technical Data ....................11 ECU Connector ....................11 Pin Count for the Connectors ................. 11 Electrical Characteristics for /TRST Signal .............. 11 Measurement Drawings ..................12 Temperature Range ....................12 Ordering Information ..................13 Contact Information ................... 14 ETAI12 User Guide... -
Page 4: About This Document
The target to be achieved is defined in the heading. The necessary steps for his are listed in a step-by-step guide: Target definition 1. Step 1 2. Step 2 3. Step 3 Result Presentation of Supporting Information NOTE Contains additional supporting information. ETAI12 User Guide... -
Page 5: Basic Safety Notices
Carefully read the documentation (Product Safety Advice and this User Guide) that belongs to the product prior to the startup. ETAS GmbH does not assume any liability for damages resulting from improper handling, unintended use or non-observance of the safety precautions. - Page 6 The product may be operated only in a technically flawless condition and according to the intended purpose and with regard to safety and dangers as stated in the respective product documentation. If the product is not ETAI12 User Guide...
- Page 7 Cabling Use exclusively ETAS cables at the connections of the product! Adhere to the maximum permissible cable lengths! Observe the assignment of the cables to the connectors! Detailed information about cabling is located in the ETK User Guides...
-
Page 8: Identifications On The Product
The user is obliged to collect the old devices separately and return them to the WEEE take-back system for recycling. The WEEE directive concerns all ETAS devices but not external cables or batteries. For more information on the ETAS GmbH Recycling software, contact the ETAS sales and service locations. -
Page 9: Ce Declaration Of Conformity (European Union)
Basic Safety Notices CE Declaration of Conformity (European Union) With the CE mark attached to the product or its packaging, ETAS confirms that the product corresponds to the applicable product-specific European Directives. The CE Declaration of Conformity for the product is available upon request. -
Page 10: Introduction
JTAG Interface. To increase the signal-noise ratio there is an buffer in the /TRST line supplied by the VDD(Sense) Voltage. The adapter is suitable for 3,3V and 5V JTAG Signals. For 5V the ETAI12 Adapter is required View Figure 2: View NOTE Minimum bending radius for the flex foil is 3mm. -
Page 11: Technical Data
ETAS Technical Data Technical Data ECU Connector In order to be able to use the ETK adapter ETAI12 in the ECU, a 10 pin SAMTEC connector (e.g. TFM-105-02-S-D-P) must be available on the ECU. Figure 3: Pin Count Pin Number... -
Page 12: Measurement Drawings
ETAS Technical Data Measurement Drawings Measured in mm Figure 5: Top View Figure 6: Side View Temperature Range Condition Temperature Operating Temperature -40°C - +110°C ETAI12 User Guide... -
Page 13: Ordering Information
ETAS Ordering Information Ordering Information Short Name Order - Number ETAI12 F 00K 109 671 ETAI12 User Guide... -
Page 14: Contact Information
Germany Internet: www.etas.com ETAS Subsidiaries and Technical Support For details of your local sales office as well as your local technical support team and product hotlines, take a look at the ETAS website: ETAS subsidiaries Internet: www.etas.com/en/contact.php ETAS technical support Internet: www.etas.com/en/hotlines.php...
Need help?
Do you have a question about the ETAI12 and is the answer not in the manual?
Questions and answers