Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Chapter 2
HARDWARE INSTALLATION
The mainboard operates with AMD
mainboard uses a CPU socket called Socket 462 for easy CPU installation.
The CPU should always have a Heat Sink and a cooling fan attached to
prevent overheating.
CPU Installation Procedures
1. Pull the lever sideways away
from the socket. Then, raise
the lever up to a 90-degree
angle.
2. Locate Pin 1 in the socket
and look for the white dot or
cut edge in the CPU. Match
Pin 1 with the white dot/cut
edge. Then, insert the CPU.
It should insert easily.
3. Press the lever down to
complete the installation.
®
TM
Duron
/Athlon processor. The
Sliding
Plate
2-1
Open Lever
Pin 1
White dot/
Cut edge
CPU
Pin 1
Close
Lever
CPU
Advertisement
Table of Contents
Related Manuals for MSI Axis 700
Summary of Contents for MSI Axis 700
-
Page 1: Hardware Installation
Chapter 2 HARDWARE INSTALLATION The mainboard operates with AMD mainboard uses a CPU socket called Socket 462 for easy CPU installation. The CPU should always have a Heat Sink and a cooling fan attached to prevent overheating. CPU Installation Procedures 1. -
Page 2: Cpu Core Speed Derivation Procedure
CPU Core Speed Derivation Procedure The mainboard CPU Bus Frequency can be set through BIOS setup. CPU Clock Core/Bus ratio then CPU core speed = Host Clock x Core/Bus ratio = 100MHz = 700MHz... -
Page 3: Fan Power Connectors: C_Fan1/S_Fan1
Fan Power Connectors: C_FAN1/S_FAN1 These connectors support system cooling fan with + 12V. It supports three pin head connector. When connecting the wire to the connec- tor, always take note that the red wire is the positive and should be connected to the +12V, the black wire is Ground and should be connected to GND. - Page 4 A battery must be used to retain the mainboard configuration in CMOS RAM. Short 1-2 pins of JBAT1 to store the CMOS data. Keep Data Note: You can clear CMOS by shorting 2-3 pin, while the system is off. Then, return to 1-2 pin position. Avoid clearing the CMOS while the system is on, it will damage the mainboard.
-
Page 5: Memory Bank Configuration
Memory Bank Configuration The mainboard supports a maximum memory size of 1.5 GB. It provides three 168-pin unbuffered DIMMs (Double In-Line Memory Module) sockets. It supports 8 MB to 512 Mbytes DIMM memory module. There are three kinds of DIMM specification supported by this mainboard: PC133, PC100 and PC66. -
Page 6: Memory Installation Procedures
Memory Installation Procedures A. How to install a DIMM Module Single Sided DIMM Double Sided DIMM 1. The DIMM slot has 2 Notch Keys “VOLT and DRAM”, so the DIMM memory module can only fit in one direction. 2. Insert the DIMM memory module vertically into the DIMM slot. Then push it in. -
Page 7: Memory Population Rules
Memory Population Rules 1. Supports only SDRAM DIMM. 2. To operate properly, at least one 168-pin DIMM module must be in- stalled. 3. This mainboard supports Table Free memory, so memory can be installed on DIMM 1 or DIMM 2 or DIMM 3 in any order. 4. - Page 8 The Keylock (reserved), Power Switch, Reset Switch, Power LED, Speaker, and HDD LED are all connected to the JFP1 connector block. Reset Switch Speaker Buzzer (short pin) Keylock (Reserved) JFP1 Power Switch Single Dual Color Color Power LED...
-
Page 9: Power Switch
Power Switch Connect to a 2-pin push button switch. Reset Switch Reset switch is used to reboot the system rather than turning the power ON/ OFF. Avoid rebooting while the HDD LED is lit. You can connect the Reset switch from the system case to this pin. Power LED The Power LED is lit while the system power is on. - Page 10 The mainboard also provides a standard floppy disk connector FDD which supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2-10...
-
Page 11: Ide1 (Primary Ide Connector)
The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA/66 Controller that provides PIO mode 0~4, Bus Master, and Ultra DMA/33/66 function. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). You can connect up to four hard disk drives, CD-ROM, 120MB Floppy (reserved for future BIOS) and other devices to IDE1 and IDE2. -
Page 12: Atx 20-Pin Power Connector: Jwr1
ATX 20-pin Power Connector: JWR1 This connector supports the power button on-board. Using the ATX power supply, functions such as Modem Ring Wake-Up and Soft Power Off are supported by this mainboard. This power connector supports instant power on function which means that system will boot up instantly when the power connector is inserted on the board. - Page 13 The mainboard provides one infrared (IR) connector for IR modules. This connector is for optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. VCC NC IRRX GND IRTX 2-13...
- Page 14 Attach a power saving switch to JGS1. When the switch is pressed the system immediately goes into suspend mode. Press any key and the system wakes up. JGS1 2-14...
-
Page 15: Pin Definition
The mainboard provides two 9-pin male DIN connectors for serial port COM A & COM B. These port are 16550A high speed communication port that send/receive 16 bytes FIFOs. You can attach a mouse or a modem cable directly into this connector. Serial Port (9-pin Male) PIN DEFINITION 1 2 3 4 5... - Page 16 The mainboard provides a 25 pin female centronic connector for LPT. A parallel port is a standard printer port that also supports Enhanced Parallel Port (EPP) and Extended capabilities Parallel Port (ECP). See connector and pin definition below: Parallel Port (25-pin Female) PIN DEFINITION SIGNAL STROBE...
- Page 17 The mainboard provides a standard PS/2 ® attaching a PS/2 mouse. You can plug a PS/2 connector. The connector location and pin definition are shown below: Pin5 Mouse Clock Pin6 Pin3 Pin4 Pin1 Mouse DATA Pin2 PS/2 Mouse (6-pin Female) The mainboard provides a standard PS/2 attaching a keyboard.
- Page 18 You can connect a joystick or game pad to this connector. Joystick/MIDI Line Out is a connector for Speakers or Headphones. Line In is used for external CD player, Tape player, or other audio devices. Mic is a connector for the microphones. Line Out Line In Mic 1/8”...
- Page 19 The mainboard provides a UHCI (Universal Host Controller Interface) Universal Serial Bus root for attaching USB devices like: keyboard, mouse and other USB devices. You can plug the USB device directly to this connector. USB Port 1 1 2 3 4 USB Port 2 SIGNAL -Data...
- Page 20 The JWOL1 connector is use for LAN add-on cards that supports Wake Up on LAN function. To use this function, set the “Wake Up on LAN/Ring” to enable located at the BIOS Power Management Setup. Note: LAN wake-up signal is active “high”. Note: To be able to use this function, you need a power supply that provide enough power for this feature.
- Page 21 The JMDM1 connector is for use with Modem add-on card that supports the Modem Wake Up function. To use this function, you need to set the “Modem Wake Up/Ring” to enable located at the BIOS Power Management Setup. Note: Modem wake-up signal is active “low”. Note: To be able to use this function, you need a power supply that provide enough power for this feature.
- Page 22 The mainboard provides a front Universal Serial Bus connector. This is an optional USB connector for Front Panel. Description USBD3- USBD3+ USB2 Description USBD2+ USBD2- 2-22...
- Page 23 This connector is for CD-ROM audio connector. JCD1 2-23...
- Page 24 This connector is for DVD Add on Card with Line In connector. JAUX1 2-24...
- Page 25 This connector is for Modem with internal voice connector. Phone_In Mono_Out J_PHN1 Mono_Out is connected to the Modem Speaker Out connector. Phone_In is connected to the Modem Microphone In connector. 2-25...
- Page 26 The mainboard provides a Special Diagnostic LED for users to be aware of their mainboard conditions. The LED helps user determine the problem of the mainboard. Diagnostic LED 2-26...
- Page 27 Diagnostic LED & Voice function D-LED 1 2 3 4 FUNCTION 0 0 0 0 System Power ON This will start the BIOS Initialization 1 0 0 0 Early Chipset Initialization 0 1 0 0 Memory Detection Test Testing Onboard memory size 1 1 0 0 Decompressing BIOS image to RAM for fast booting...
- Page 28 The Smart D-LED is a voice mode tool, which literally helps the users to identify the cause of any possible failure. This works through a recorded voice either in English or Chinese language. English Chinese Mode Mode 2-28...
- Page 29 The Communication Network Riser specification is an open industry- standard specification that defines a hardware scalable Original Equipment Manufacturer (OEM) mainboard riser board and interface, which supports audio and modem only. 2-29...