Table of Contents
Advertisement
Page
Contents
1.
2
2.
3
3
3
3
4
6
6
7
4.
8
8
9
5.
10
6.
10
VOLERO WAVE
INSTRUCTION MANUAL
INDEX
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the
rich Claypaky range, has been designed and made with
total quality to ensure excellent performance and best
meet your expectations and requirements.
CL3023
Advertisement
Table of Contents
Related Manuals for Clay Paky VOLERO WAVE
Summary of Contents for Clay Paky VOLERO WAVE
-
Page 1: Table Of Contents
CL3023 VOLERO WAVE INSTRUCTION MANUAL INDEX Congratulations on choosing a Claypaky product! Page Contents We thank you for your custom. Safety information Please note that this product, as all the others in the rich Claypaky range, has been designed and made with... -
Page 2: Safety Information
IMPORTANT: Claypaky recommande de lire attentivement et de conserver les informations de sécurité relatives à ce produit, disponibles en version digitale au lien suivant: www.claypaky.com Réf. : FIS02D - Safety Information Volero Wave ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ ВАЖНО: Claypaky рекомендует внимательно прочитать и сохранить инструкцию по технике безопасности... -
Page 3: Unpacking And Preparation
2. UNPACKING AND PREPARATION Packing contents - Fig. 1 3. INSTALLATION AND START-UP 3.1 Fixture overview ON / OFF Neutrik PowerCON TRUE1 (IN/OUT) Functional buttons LCD Display 5pin DMX IN/THRU Ethernet Safety loop Continue VOLERO WAVE... -
Page 4: Installing The Fixture
The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall. WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105041-003 available upon request). This must be secured to the projector support structure and then hooked to the two fastening points. VOLERO WAVE... - Page 5 Projector installation - Fig. 4 Continue VOLERO WAVE...
-
Page 6: Connecting To Mains Supply
A terminating plug must be inserted on the last projector with a resistance of 120 (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield braid and pin 1 of the connectors. VOLERO WAVE... -
Page 7: Switching On The Fixture And Basic Setup
3.5 Switching on the fixture and basic SetUp Switching on the projector - Fig. 8 The projector immediately turns on when the power cord is plugged. Clay Paky Volero Wave Address xxx Volero Wave Software release x.x x xxxxx ??? * The control panel (Figure 8) has a display and buttons for complete programming and management of the projector menu. -
Page 8: Maintenance
- Electrical, photometric and functional checks; eventual repairs. Cleaning the lenses Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other detergent could damage the lenses). VOLERO WAVE... -
Page 9: Battery Removal
4.2 Battery removal This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. VOLERO WAVE... -
Page 10: Dimensions
Call an authorised technician. Signal transmission cable faulty or disconnected. Replace the cables. Incorrect addressing. Check addresses (see instructions). Fault in the electronic circuits. Call an authorised technician. Optic fault. Call an authorised technician. Dust or grease deposits. Clean (see instructions). VOLERO WAVE... - Page 11 VOLERO WAVE...
- Page 12 CLAYPAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - www.claypaky.com S.p.A.
Need help?
Do you have a question about the VOLERO WAVE and is the answer not in the manual?
Questions and answers