Related Manuals for e-con Systems See3CAM CU135
Summary of Contents for e-con Systems See3CAM CU135
- Page 1 See3CAM_CU135 Camera DFU Application User Manual Version 1.0 e-con Systems 1/11/2017...
- Page 2 Disclaimer e-con Systems reserves the right to edit/modify this document without any prior intimation of whatsoever. © Copyright e-con Systems. 2017. All rights reserved.
-
Page 3: Table Of Contents
Contents INTRODUCTION TO FIRMWARE INSTALLING THE SEE3CAM_DFU APPLICATION 1 - W ELCOME CREEN 2 - I NSTALLATION ELECTION 3 - R EADY TO NSTALL INDOW 4 - A TTACHING THE EVICE USING THE SEE3CAM_DFU APPLICATION 1 - D EVICE ELECTION 2 - F IRMWARE ELECTION... -
Page 4: Introduction To Firmware
See3CAM device. This document highlights the process of updating a new firmware in the See3CAM product. In future to add new functionalities to the See3CAM device, e-con Systems will release new firmware binary. You can update this firmware into the See3CAM device by using the See3CAM_DFU application. -
Page 5: Installing The See3Cam_Dfu Application
Step 2 - Installation Path Selection To select the installation path, you can either use the default installation path C:\Program Files\e-con Systems\See3Cam_DFU\ or can change to another installation path. After choosing the installation path, you can click the Next button as shown below. -
Page 6: Step 3 - Ready To Install Window
To begin the installation, you can click the Install button as shown below. Figure 3: Ready to Install Window Step 4 - Attaching the Device The See3CAM device can be attached to the PC, and you can view the completion window as shown below. © Copyright e-con Systems. 2017. All rights reserved. - Page 7 Figure 4: Completion Window Click the Finish button to exit the Setup Wizard. See3CAM_DFU Application User Manual...
-
Page 8: Using The See3Cam_Dfu Application
Click the Device drop-down list which lists all the devices connected to the PC and select the camera to update the firmware as shown below. Figure 5: Device Selection If no devices are connected for update, No Device Connected label will be displayed as shown below. © Copyright e-con Systems. 2017. All rights reserved. -
Page 9: Step 2 - Firmware Selection
Figure 6: Drop-down List Empty when no See3CAM Device is Connected Step 2 - Firmware Selection Click the Browse key and select the firmware image file as shown below. Figure 7: Firmware File Selection Window You can verify the product name and the firmware version before proceeding. Click the Open group on the Home tab to view the firmware image. - Page 10 You can switch the device to Firmware Update mode and can start erasing the Old Firmware as shown below. Figure 9: Switching to e-con DFU and Erasing the Old Firmware The application reads the firmware file and updates it into the device as shown below. © Copyright e-con Systems. 2017. All rights reserved.
-
Page 11: Step 4 - Firmware Update Complete
Figure 10: Firmware Update in Process Warning: Do not disturb the Universal Serial Bus (USB) connection or unplug the camera when the firmware update is in process. Step 4 - Firmware Update Complete Once the progress bar reaches 100%, the device will automatically reset and gets detected with new firmware as shown below. - Page 12 Firmware Download Failed! message as shown below. Figure 13: Firmware Update Failure In this case, the device is connected as e-conDFU_USB_1_HUB_0(VID_2560, PID_DF00_0 as shown below. © Copyright e-con Systems. 2017. All rights reserved.
- Page 13 Figure 14: Device in e-con DFU Mode You can again follow the steps 1 to 4 to retry the firmware update process. See3CAM_DFU Application User Manual...
-
Page 14: Troubleshooting
It seems like device firmware is corrupted. You need to try re-flashing firmware image using firmware updater application from developer website. If this does not help, contact e-con Systems online support support@e-consystems.com. © Copyright e-con Systems. 2017. All rights reserved. -
Page 15: Faq
External trigger option in See3CAM_CU135. 4. What sort of support does e-con Systems provides along with the camera? e-con Systems will provide the basic support on the evaluation for all the customers who have purchased the camera. e-con Systems will provide the hardware/software/firmware customization of the kit based on your requirements. - Page 16 If your application requires fixed focus custom lens, contact sales@e- consystems.com. The Non-recurring engineering (NRE) refers to the one-time cost to research, design, develop and test a new product or product enhancement. © Copyright e-con Systems. 2017. All rights reserved.
-
Page 17: What's Next
What’s Next? After understanding the usage of DFU application, you can refer to the following documents to understand more about See3CAM_CU135. • e-CAMView_Streaming_Application_User_Manual_of_See3CAM_CU135 • Release Notes of See3CAM_CU135 See3CAM_DFU Application User Manual... -
Page 18: Support
Policy page on our website - https://www.e-consystems.com/RMA-Policy.asp General Product Warranty Terms To know about our General Product Warranty Terms, please visit the General Warranty Terms page on our website - https://www.e- consystems.com/warranty.asp © Copyright e-con Systems. 2017. All rights reserved. - Page 19 Revision History Date Description Author 28-February-2017 Initial Draft Camera Dev Team See3CAM_DFU Application User Manual...