Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for e-con Systems e-CAM50_CU96
Summary of Contents for e-con Systems e-CAM50_CU96
- Page 1 Getting Started Manual Version 1.0 e-con Systems 1/8/2020...
- Page 2 Disclaimer The specifications of e-CAM50_CU96 board and instructions on how to use this board with ROCK960 development board are provided as reference only and e-con Systems reserves the right to edit/modify this document without any prior intimation of whatsoever. © Copyright e-con Systems. 2020. All rights reserved.
-
Page 3: Table Of Contents
Contents INTRODUCTION TO E-CAM50_CU96 ARTS UPPLIED ESCRIPTION E-CAM50_CU96 BOARD HANDLING PROCEDURE PREPARING SD CARD WITH PREBUILT BINARY STREAMING OF E-CAM50_CU96 BOARD GLOSSARY SUPPORT e-CAM50_CU96 Getting Started Manual... -
Page 4: Introduction To E-Cam50_Cu96
Introduction to e-CAM50_CU96 e-CAM50_CU96 is 5 MP customer lens camera module designed and developed by e-con Systems, a leading Embedded Product Design Services Company which specializes in advanced camera solutions. e-CAM50_CU96 targets the ROCK960 development board. It can be interfaced with ROCK960 development board through the high speed and low speed camera interface connectors. -
Page 5: Description
GHz and Cortex A53 Quad-core up to 1.4 GHz CPU. The ROCK960 development board supports two camera interfaces, HDMI, microSD Slot, USB 3.0, Ethernet, Audio Out, and so on. e-CAM50_CU96 is a multi-board solution, which has three boards as follows: • Camera module (e-CAM55_CUMI0521_MOD) •... - Page 6 CMOS image sensor with an electronic rolling shutter. The front and rear views of the boards are shown in below figures. Figure 1: Rear View of e-CAM55_CUMI0521_MOD Board Figure 2: Front View of eCAM130_TRICUTX2_ADAPTOR Adaptor Board © Copyright e-con Systems. 2020. All rights reserved.
- Page 7 Figure 3: Rear View of eCAM130_TRICUTX2_ADAPTOR Adaptor Board Figure 4: Front View of ACC-96DEV_MIPICAMERA_ADP Figure 5: Rear View of ACC-96DEV_MIPICAMERA_ADP e-CAM50_CU96 Getting Started Manual...
- Page 8 20-pin Samtec connectors (CN1 and CN3) for mating with e-CAM50_CU96 module board and a 30-pin I-PEX connector (CN2) for connecting with e-CAM50_CU96 base board. Both the module board and adapter board are screwed into a single unit. This single unit should not be separated. This adaptor board acts as a bridge between the camera module and the base board.
-
Page 9: E-Cam50_Cu96 Board Handling Procedure
This section describes the handling procedure of e-CAM50_CU96 board. The procedure to assemble camera board are as follows: 1. Connect CN4 and CN5 connectors of e-CAM50_CU96 base board with high speed and low speed camera interface connectors in the ROCK960 development board. - Page 10 2. Connect Pin 1 of CN4 connector with Pin 1 of high speed camera interface connector and Pin 1 of CN5 connector with Pin 1 of low speed camera Interface connector. The ROCK960 development board with e-CAM50_CU96 base board is shown in below figure. Figure 8: ROCK960 Development Board with e-CAM50_CU96 Base Board 3.
- Page 11 Figure 11: Location of CN2 Connector on Base Board The locking and unlocking positions of micro-coaxial cable on the base board connector are shown in below figures. Figure 12: Unlocking Position of Cable on Base Board CN2 Connector e-CAM50_CU96 Getting Started Manual...
- Page 12 Figure 14: e-CAM50_CU96 Setup Interfaced to ROCK960 Development Board 6. Insert the memory card provided by e-con Systems in the SD card slot before powering ON. The location of SD card slot in ROCK960 development board is shown in below figure.
- Page 13 8. Connect a DC power with 12V 2A to power ON the ROCK960 development board as shown in below figure. After powering ON the ROCK960 development board, the green color LED on ROCK960 development board will glow. This serves as an indication for power- up of board. e-CAM50_CU96 Getting Started Manual...
-
Page 14: Preparing Sd Card With Prebuilt Binary
Warning: If wrong device node is mentioned, the data loss in corresponding device may occur. 9. Run the following command to synchronize the disk write process, once SD card flashing is completed. © Copyright e-con Systems. 2020. All rights reserved. - Page 15 $ sync Now the SD card is flashed with system image for ROCK960 board. The operating system flashed on the microSD card is Debian GNU/Linux 9.2 (stretch). e-CAM50_CU96 Getting Started Manual...
-
Page 16: Streaming Of E-Cam50_Cu96 Board
Streaming of e-CAM50_CU96 Board This section describes the steps to stream e-CAM50_CU96 board. The steps to stream e-CAM50_CU96 board are as follows: 1. Unplug ROCK960 board from power. 2. Connect the ROCK960 board HDMI interface with HDMI cable. 3. Connect the USB keyboard and mouse using USB hub present in the ROCK960 board. - Page 17 $ gst-launch-1.0 rkcamsrc device=/dev/video0 io- mode=dmabuf ! video/x-raw, width=<WIDTH>, height=<HEIGHT>, framerate=60/1 ! fpsdisplaysink video-sink=rkximagesink text-overlay=false -v Where, <WIDTH>=width of the frame (example: 1920), <HEIGHT>=height of the frame (example: 1080) which can be changed as per the requirement. e-CAM50_CU96 Getting Started Manual...
-
Page 18: Faq
1. What is e-CAM50_CU96? e-CAM50_CU96 is 5 MP camera module designed and developed by e-con Systems, a leading Embedded Product Design Services Company which specializes in advanced camera solutions. 2. What is the camera sensor used in the eCAM50_CU96 design? eCAM50_CU96 camera module is based on 1/2.5"... - Page 19 16. What are the supported OSes for eCAM50_CU96 with Rock960? The supported OSes for eCAM50_CU96 with Rock960 is Debian GNU/Linux 9.2 (stretch). In future, e-con Systems planned to provide AOSP support. For customization, please write to sales@c-onsystems.com. 17. How many cameras can I connect with Rock960 boards? Currently one camera is supported.
- Page 20 23. Can I get the mechanical 2D and 3D files for the eCAM50_CU96 PCB? Yes. Please write to sales@e-consystems.com for the PCB files. 24. What are the warranty terms of the e-CAM50_CU96 camera? Please refer this www.e-consystems.com/warranty.asp page for warranty terms.
-
Page 21: Glossary
UYVY: YUV422 16-bit image format with UYVY ordering. VGA: Video Graphics Array (Industry name for 640 x 480 resolution). V4L2: Video for Linux version 2 is a collection of device drivers and API for supporting real-time video capture on Linux systems. e-CAM50_CU96 Getting Started Manual... -
Page 22: Support
Support Contact Us If you need any support on e-CAM50_CU96 product, please contact us using the Live Chat option available on our website - https://www.e-consystems.com/ Creating a Ticket If you need to create a ticket for any type of issue, please visit the ticketing page on our website - https://www.e-consystems.com/create-ticket.asp... - Page 23 Revision History Date Description Author 08-January-2020 Initial draft Camera Team e-CAM50_CU96 Getting Started Manual...