Water Connection - Black & Decker BEPW1300 Manual

ENGLISH
Self Priming under Preparing Pressure Washer Unit
for Use.
2. Connect the high pressure hose to the pressure washer
and the spray handle. For instructions on connecting the
high pressure hose to the pressure washer and spray
handle, please refer to Attaching High Pressure Hose
under Assembly and Adjustments.
3. Connect the garden hose to the pressure washer. For
instructions on connecting the water supply to the
pressure washer, please refer to Attaching Garden Hose
under Assembly and Adjustments.
4. Plug the power cord into an appropriate power source.
Preparing Spray Handle (Fig. A)
IMPORTANT: Before turning on the pressure washer
unit, disengage the trigger lock‑off ( 6 ) and squeeze the
trigger ( 7 ).
1. Disengage the trigger lock‑off ( 6 ) .
2. Squeeze the trigger ( 7 ). Hold the trigger for 30 seconds
to purge the system of air.
3. If air is still found in the water stream, continue to run
water through the spray handle.
@

Water Connection

WARNING: According to the applicable
regulations, the appliance must never
be used on the drinking water network
without a system seperator. Use a
system seperator as per IEC
61770 Type BA.
Water flowing through a system seperator is not
considered drinkable.
• Comply with the regulations of your water supply company.
• All connecting hoses must have properly sealed joints.
• Make sure the supply hose is at least 12.7 mm in diameter
and is reinforced.
• The appliance should never be used on the drinking water
supply without a backflow valve. Water that has passed
the backflow valve is considered undrinkable.
Cleaning a Surface (Fig. A)
1. To start the pressure washer, rotate the ON/OFF dial ( 17 )
to the ON position.
2. Confirm that the water faucet is open or use any other
water source so that water will be supplied to the pressure
washer unit.
3. The best angle for spraying water against a cleaning
surface is 45 °.
Spraying head on tends to cause dirt particles to
-
imbed in the surface.
When working on vertical surfaces, it is best to apply
-
detergent starting at the bottom and working upwards
12
(Original instructions)
which will prevent the detergent from sliding down and
causing streaks.
4. To disengage the spray handle, release the trigger.
NOTE: Excessive pump pressure may be the result of a
clogged nozzle. Always turn OFF the pressure washer unit
and unplug the unit before attempting to unclog a nozzle.
Detergents (Fig. J1, J2, J3, J4)
For steps on attaching the detergent/soap bottle, please
refer to Attaching Soap Bottle under Assembly
and Adjustments.
The use of detergents can dramatically reduce cleaning time
and assist in the removal of difficult stains. Some detergents
have been customized for pressure washer use on specific
cleaning tasks.
The cleaning power of detergents comes from applying them
to a surface and giving the chemicals time to break down
the dirt and grime. Detergents work best when applied at
low pressure.
The combination of chemical action and high pressure rinsing
is very effective.
On vertical surfaces, apply the detergent starting at the bottom
and work your way upward. This will prevent the detergent
from sliding down and causing streaks. High pressure
rinsing should also progress from the bottom to top. On
particularly tough stains, it may be necessary to use a brush in
combination with detergents and high pressure rinsing.
Moving the Pressure Washer (Fig. A)
1. Turn OFF the pressure washer unit ( 16 ) by rotating the
ON/OFF dial ( 17 ) to the OFF position and then turn OFF
the water supply.
2. Point the spray wand ( 2 ) in a safe direction and pull the
trigger ( 7 ) to release remaining water pressure.
3. When the spray wand is completely empty, lift the
pressure washer by the handle ( 18 ).
Shutdown (Fig. A, D)
1. Turn OFF the pressure washer unit ( 16 ) by rotating the
ON/OFF dial ( 17 ) to the OFF position and unplug the
cord from the outlet.
2. Turn OFF water at the faucet or disconnect from any other
water source.
3. Discharge residual pressure by squeezing the trigger ( 7 )
until no more water comes out of the spray wand ( 2 ).
4. Engage the spray trigger lock‑off ( 6 ).
5. Disconnect the garden hose ( 28 ) from the water
intake ( 25 ).
6. Disconnect the high pressure hose ( 1 ) from the high
pressure water outlet ( 20 ) and drain hose.