Kolver LINAR2 Manual

Folding and linear positioning arms with autoadvance kit

Hide thumbs

page of 20

/ 20
Bookmarks

Quick Links

Download this manual

Folding and Linear Positioning Arms with Autoadvance Kit

Only Autoadvance kit to be installed on Kolver code 020099

Code

010682/A

TLS1/LINAR2 with

010682/TLS1/A

IDENTIFICATION DATA OF THE MANUFACTURER

VIA M. CORNER, 19/21

36016 THIENE (VI) ITALIA

IDENTIFICATION DATA OF THE PRODUCT

MODEL:

CODE:

TECHNICAL DATA OF THE PRODUCT

ELECTROVALVE TENSION: 24V DC 0,35W

ARM DIMENSIONS: 684 x 191.13 x 722,5h mm

ARM WEIGHT: 5,7 Kg

AUTOADVANCE KIT WEIGHT 0,4 Kg

Model

LINAR2 with

Autoadvance kit

Manual

KOLVER S.r.l.

LINAR2

TLS1/LINAR2

010682/A

010682/TLS1/A

Stroke mm

Torque

Max

Min

Max

50 Nm

184

50 Nm

184

Piston stroke

665

0-50

665

0-50

Min distance

between screws at

the max arm

extension

6 mm

Need help?

Do you have a question about the LINAR2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Kolver LINAR2

Page 1 LINAR2 TLS1/LINAR2 CODE: 010682/A 010682/TLS1/A Only Autoadvance kit to be installed on Kolver code 020099 TECHNICAL DATA OF THE PRODUCT ELECTROVALVE TENSION: 24V DC 0,35W ARM DIMENSIONS: 684 x 191.13 x 722,5h mm ARM WEIGHT: 5,7 Kg AUTOADVANCE KIT WEIGHT 0,4 Kg...
Page 2 Autoadvance Kit The Autoadvance arm kit is a particular device that mounted on a Kolver Linar2 or Linart arm helps the operator in the assembly of self-tapping screws or in case of strong axial thrust. Through a pneumatic piston, the part of the arm that supports the screwdriver is pushed down to help the axial thrust on the screw.
Page 3 AUTOADVANCE KIT EXPLODED VIEW Vers. 210422...
Page 4: Spare Parts
SPARE PARTS Position DESCRIPTION Code RACCORDO SILENZIATORE 895094 ELETTROVALVOLA 895092 SUPPORTO ELETTROVALVOLA 895096 VITE M3x10 231530 RACCORDO ARIA 90° M5 TUBO 4MM 250073 ANELLO DI TEFLON AUTOAVANZANTE 895084 BOCCOLA DI GUIDA AUTOAVAZANTE 895080 MOLLA INTERNA AUTOAVANZANTE 895088 PERMAGLIDE AUTOAVANZANTE 895091 TUBO 4MM 250075 CILINDRO 12MM CORSA 50MM DOPPIO...
Page 5 Electrovalve Specifications Vers. 210422...
Page 6 Fluid 0,15 – 0,7 MPa Operating pressure Ambient and fluid temperature -10 - 50 °C Max operation frequency 10 Hz Pilot exhaust method Common exhaust type Lubrification Not required Impact/vibration (m/s²) 150/30 Enclosure Dust proof Terminal IP65 Coil rated voltage 24 V ±10% Power consumption 0,35 W...
Page 7 Electrical connection Connect the supplied cable (code 895092/2M) to the electrovalve through the appropriate connector. Vers. 210422...
Page 8 The red cable must be connected to the 24V “lever / W” or “Motor ON” signal present in the Output connectors of the Kolver units; while the black one will be connected to the common 0VDC.
Page 9 I/O Kolver unit connection to advance arm Model Code Electrovalve cable Electrovalve cable +24V Red wire 0V Black wire EDU 1FR/SG/W 010010/FR/SG/W Pin 6 Pin 1 EDU 1BL/SG/W 003000/SG/W Pin 7 Pin 9 EDU 2AE Series Pin 4 CN1 Pin 2 CN1...
Page 10 Cylinder Vers. 210422...
Page 11 Force 1 decaNewton [daN] = 10 N 1 decaNewton [daN] = 1,02 Kgf Vers. 210422...
Page 12 Mounting Insert the pneumatic cylinder into the hole of the fixing ring. Secure the cylinder with the 22mm nut, keep the pneumatic fittings aligned laterally as shown in the figure. Vers. 210422...
Page 13 Connect the cylinder to the push bracket. Fix the stem to the bracket up to the stop using the 5mm wrench. Secure the lock nut with a 10mm wrench. Vers. 210422...
Page 14 Place the bushing on the vertical bearing support. Join the assembled kit to the arm holder plate. Vers. 210422...
Page 15 Align in the cylinder holder the fixing holes to the holes in the arm holder plate. Then fasten the screws. Insert the kit mounted on the sliding rod. Vers. 210422...
Page 16 NB. In order to move manually the self-advancing block in the rod it is necessary to keep it pressed on the vertical bearing support in order to simulate the closing of the piston. If no pressure is exerted, the self- advancing block does not allow the arm to slide upwards.
Page 17 Hook the balancer cable to the lifting screw. Protective hood assembly The protection cap allows it to be mounted / dismounted on the self- advancing block at the end of the entire assembly. Vers. 210422...
Page 18 Pneumatic connections Electrovalve mounting to the support Electrovalve mounting to the balancer Vers. 210422...
Page 19 Connection on the electrovalve Connection on the piston Regolator Piston return speed Air regolator Clockwise: flow closure Counterclockwise: flow opening Regolator Piston push speed Vers. 210422...
Page 20 7. No one, whether an agent, servant or employee of KOLVER, is authorized to add to or modify the terms of this limited guarantee in any way. However it’s possible to extend the warranty with an extra cost.

This manual is also suitable for:

Tls1/linar2 010682/a 010682/tls1/a