Lorex LNZ4001 Quick Setup Manual

LNE Series
Quick Setup Guide

BEFORE YOU START

This Network Camera is designed for easy installation.
However, before you continue, please read the following:
The Quick Start Guide refers to LNE1001, LNE3003 and LNZ4001
models and must be followed in sequence without
skipping steps.
1. When setting up the camera, use Internet Explorer only
After the initial setup, you can view the camera using Internet
Explorer (with ActiveX), Mozilla Firefox and
Safari
2. Steps 1 - 2 should to be completed when your camera is
connected wired before you can use the camera wirelessly.
3. When connecting the camera to a wireless network, consider the
following:
a. If your wireless router is not set up with wireless encryption, you
can start the installation process immediately.
b. If your wireless router is set up with the encryption, please make
sure you know the encryption key. If you do not know the
encryption key (encryption password), please refer to your
router's manual in order to reset the key.
c. If your wireless router is set up with a different type of encryption
please refer to your router's manual in order to change
encryption type to WEP.
d. The camera is compatible with Macintosh for viewing only.
Recording on Macintosh is not supported. To set up camera using
Macintosh auto discovery "Bonjoure" can be used, advanced
knowledge is required. Please refer to "Setting Up Using
www.lorexcctv.com
Macintosh" FAQ on LOREX web site
SET UP YOUR CAMERA FIRST
It really is that easy!
Broadband Router and Computer are required for
local and remote monitoring (not included).
Set up Your Camera
a
Place the base of the
camera on a flat surface
and screw on the stand.
b
SEE HEAR PROTECT
Attach the screw knob to
ALSO AVAILABLE:
the camera stand.
16-CHANNEL INTELLIGENT SURVEILLANCE
c
SOFTwARE SOLUTION
LDP1601
Enhance your security with genuine Lorex Cameras, Digital Video Recorders,
Integrated Systems and Accessories. Order whatever you need at
www.lorexcctv.com or call 1-888-42-LOREX (1-888-425-6739)
Warehouse Offi ce Restaurant Convenience Store
Attach the wireless antenna to
the back of the camera.
LNP5220E, LNP5320E, LNE3003 , LNP5220E, LNP5220E, LND7220V LND7220V, LNE3003
LND7220V, LNZ9320W LND7220V
d
Day Care PROTECT EVERYTHING Home Offi ce
THAT MATTERS
Add wired or wireless network cameras to
expand the "Envelope of Protection" for your
business, your home and your family
LNE3003
LNE3003, LNP5220E
Drive Way / Parking Lot Front Door Nursery Backyard
Screw the camera to the
camera stand.
e
LNP5320E, LNB6300V LNE3003 LNZ4001 LNE3003 LNE1001 LNP5320E, LND7220V
It's all on the web www.lorexcctv.com
For detailed setup information, please refer to
your User's Manual. For additional information,
please visit our website www.lorexcctv.com
Tighten the screw knob to
Information in this document is subject to change without notice. As our products are subject secure the camera.
to continuous improvement, Lorex Technology INC. and our subsidiaries reserve the right to
modify product design, specifications and prices, without notice and without incurring any
obligation. E&OE © 2009 LOREX. All rights reserved.
iPhone™, iPod touch™, Yoics™, and MSN™ are registered trademarks of their respective
companies, registered in the United States and other countries. iPhone™ and iPod touch™ are
not included in this package.
Time
DISCOVER & VIEw YOUR CAMERA
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
ON THE LOCAL NETwORK
Time
Hand Tools Hardware Hi Speed
BASI C I NSTAL L ATI ON GU I DE
Router
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Time: 10 Minutes Hand Tools Skills - Easy
STEP 1 STEP 2
Skill Level
Hand Tools Hardware Hi Speed
Router
easy Intermediate advanced
Skill Level NOTE: This quick start guide refers to a Windows Vista™, installation.
Pop-up security windows may differ in Windows XP™. Installation is
easy in both versions of the operating system.
Intermediate advanced
easy
NOTE: For initial setup, you will need Internet Explorer as your
default browser. Do not install DigiConsole until Step 2 is completed.
IMPORTANT
f
Launching the DigiConsole Software
Connect the included network
Before launching the program, please make sure your computer is connected
cable to the rear side of the
to the same local network as the camera and has access to the Internet.
LAN port on the bottom of the
The camera must be connected using the included Ethernet cable for initial
camera. Connect the other
installation. It is recommended to setup the camera when your computer is
end of the network cable to the
wired to the local network. If you are using the wireless connection on your
router, switch, or active wall
computer, please make sure you are connected to your wireless router (check
port of your local network.
wireless name - SSID).
g
Insert the included
a
DigiConsole Software CD into
your CD/DVD-ROM drive.
If the software runs
b
automatically, please
proceed to Step 2, section d.
Plug the power adaptor into the
power port of the camera. Plug the
If the pop-up window
other end to an electrical outlet.
appears, click Run
NOTE: Make sure the LED is lit
DigiConsole.exe and
on the front of the camera. If not,
continue to Step 2, section c.
check that all cables are properly
connected.
1
LNE3003
2
3
Local Viewing
5 4
LNZ4001
Double-click the camera to
a
1 launch DigiViewer in your
browser.
2
3
6 7 8
Enter admin in the username
b
4
5 and admin in the password
fields to access your camera.
1. Camera 5. Reset
The browser will prompt you
2. Antenna 6. Audio IN
3. Power Adaptor Port to install ActiveX.
7. Audio OUT
4. Ethernet Cable
8. I/O
(LAN) Port
Depending on your browser
security settings, you can use the
"remember me" check option and
the next time you will view the
same camera using this browser
it will renumber user name and
password till you restart your
computer.
Time
USING ZOOM AND PAN/TILT FEATURE
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Hand Tools Hardware Hi Speed
BASI C I N STALLATIO N GUI DE BAS IC IN S TAL LATI O N GU IDE
Router
Time: 10 Minutes Hand Tools Skills - Easy Time: 10 Minutes
STEP 3
- Computer
Skill Level
easy Intermediate advanced
NOTE: This step refers to LNZ4001 camera model and shows only basic
functionality of Pan/Tilt feature. For a full instruction on all Pan/Tilt
functionality, please refer to manuals in CD
From DigiViewer, once you are
a
able to view the video using the
browser, click the PTZ icon
A Pan/Tilt control panel will
appear on the left side of
DigiViewer.
If a security pop-up window
c
appears, click Unblock
and Continue to allow
DigiConsole to run.
Click the arrows to control Pan
b
NOTE: If the CD does not start
and Tilt.
automatically, please go to "Computer"
Preset & Patrol
("My Computer" for Windows XP™ users)
and double click on the CD Drive to run Zoom IN
the application. Follow Step 2.
Zoom Out
Click Find to discover Lorex
d
Navigation Arrows
cameras on your network.
Preset & Patrol:
NOTE: The Preset and Patrol are
OPTION: If UPNP is enabled on your
advanced features, for a full instruction
computer open the "Network" ("My
on setting up these features; please
Network Places" for Windows XP™
users) folder to view UPnP devices. refer to manuals in CD.
(UPNP is disabled by default in
Using the arrows, position the
c
Windows Vista™).
camera to point to where you
want it to patrol. From the Pan/
Tilt control panel click Set.
If a security pop-up window
c
appears, click Unblock
and Continue. Click the
warning on the browser bar
and select Install ActiveX
Control. Click Unblock or
Continue in any proceeding
Then click the Set button beside
security pop-ups.
Preset Go.
Click the warning bar (it will turn from
yellow to blue) and select Install ActiveX.
Click Install to start the
d
installation. Click Unblock or
Click Go Back. Repeat step C until
Continue in any security you complete the Patrol positions
pop-up. (This step is required you require. (You can set up to 32
positions; each Tour can have up to
only for first time set-up).
8 positions).
Congratulations! Your camera is Congratulations! Your camera is now
now set-up for local viewing set-up for Zoom and Pan/Tilt feature
Time
under 15 minutes under 30 minutes under 60 minutes over 60 minutes
Hand Tools Hardware Hi Speed
Router
Hand Tools Skills - Easy
- Computer
Skill Level
easy Intermediate advanced
• From DigiViewer, click
d
Events and then select
Patrol.
.
• Select the Tour number
(E.g.: Tour 1)
• Select Order (first will be
the default position)
• Select Preset Position (the
positions you set in Step 3c),
then click Set.
Repeat the order and position
selection until you have
your tour completed with all
required positions (each Tour
can have up to 8 positions).
Click Submit Patrol.
• From DigiViewer,
e
click the
Surveillance, click
the Play icon and
click the PTZ icon .
• From Pan/Tilt control
panel click Set then
click the Set button
beside Patrol Go.
• Select the Tour
number you set up in
Step 3d and click the
Patrol Go button.