Table of Contents
Advertisement
Quick Links
Note
Contents
Get user manuals:
See SafeManuals.com
Installing the Cisco WAE Inline Network Adapter
Product Number: WAE-INLN-4CG=
Models: FE-511-K9, WAE-511-K9, WAE-611-K9, WAE-512-K9, WAE-612-K9, WAE-7326-K9, WAE-7341-K9,
WAE-7371-K9, WAE-674-K9
This document describes how to install the Cisco WAE inline network adapter in your edge or core WAE
appliance. These instructions are intended for experienced technicians.
The Cisco WAE inline network adapter is not supported in a Central Manager appliance. (For more
information, see the
"Important Operational Notes" section on page
This document contains the following sections:
Product Overview
•
Safety Guidelines
•
•
Important Operational Notes
Installing Adapters in the FE-511, WAE-511, and WAE-611 Appliances
•
Installing Adapters in the WAE-512 and WAE-612 Appliances
•
•
Installing Adapters in the WAE-7326 Appliance
Installing Adapters in the WAE-7371, WAE-7341, and WAE-674 Appliances
•
•
Cabling
Related Documentation
•
Obtaining Documentation, Obtaining Support, and Security Guidelines
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
© 2007–2008 Cisco Systems, Inc. All rights reserved.
7.)
Advertisement
Table of Contents
Related Manuals for Cisco WAE-INLN-4CG Series
Summary of Contents for Cisco WAE-INLN-4CG Series
- Page 1 Models: FE-511-K9, WAE-511-K9, WAE-611-K9, WAE-512-K9, WAE-612-K9, WAE-7326-K9, WAE-7341-K9, WAE-7371-K9, WAE-674-K9 This document describes how to install the Cisco WAE inline network adapter in your edge or core WAE appliance. These instructions are intended for experienced technicians. The Cisco WAE inline network adapter is not supported in a Central Manager appliance. (For more...
-
Page 2: Product Overview
WAAS software version 4.2.1 or later. The inline network adapter is a full-height, three-quarter-length PCI-X network interface card that contains four independent Gigabit Ethernet ports. (See Figure Figure 1 Inline Network Adapter Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com... -
Page 3: Ports And Led Indicators
WAE without being processed. For more information about configuring the inline network adapter, see the Cisco Wide Area Application Services Configuration Guide. -
Page 4: Adapter Specifications
PCI connector Universal 64-bit connector PCI voltage +12 V (minimum 11.4 V, maximum 12.6 V) +3.3 V (minimum 3.0 V, maximum 3.6 V) Weight 6.18 oz (175 grams) Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com... -
Page 5: Safety Guidelines
This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals:... -
Page 6: General Precautions
General Precautions Observe the following general precautions for using and working with your system: Observe and follow service markings. Do not service any Cisco product except as explained in your • system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt may expose you to electrical shock. -
Page 7: Protecting Against Electrostatic Discharge
Important Operational Notes If you intend to reconfigure an edge or core WAE with a Cisco WAE inline network adapter installed in it as a Central Manager device, first remove the inline network adapter. The inline network adapter is not supported in a Central Manager appliance. -
Page 8: Removing The Cover
For proper cooling and airflow, replace the cover before turning on the appliance. Operating the Caution appliance for extended periods (over 30 minutes) with the cover removed might damage appliance components. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com... - Page 9 You must install PCI expansion slot covers on all vacant slots so that you can maintain the Note electronic emissions characteristics of the appliance and ensure proper cooling of internal components. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 10 Expansion slot cover (slot 1) Captive screw Riser card assembly Remove the riser card (labeled 1 in Figure 5) from the system board to access the expansion slot. Step 6 Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 11 To install the adapter, carefully grasp the adapter by its top edge or upper corners, align it with the PCI-X slot 1 connector (labeled 3 in Figure 5), and then press the adapter firmly into the expansion slot. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
-
Page 12: Completing The Installation
Before sliding the cover forward, make sure that the cover will properly engage the ledge at the front of Caution the appliance. Figure 6 Installing the Cover Install the appliance in the rack. Step 2 Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com... - Page 13 Step 4 slightly with your other hand, and using your free thumb, slide the cover back approximately 0.5 inches (1.27 cm); then lift it up and off the device. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals:...
- Page 14 Step 3 Step 4 Remove the device cover. Grasp the riser card at the rear edge and lift to remove the riser card assembly. (See Figure Step 5 Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 15 You must install PCI expansion slot covers on all vacant slots so that you can maintain the Note electronic emissions characteristics of the appliance and ensure proper cooling of internal components. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 16 Reinstall the riser card. Make sure that the riser card is fully seated in the riser card connectors on the Step 11 system board. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 17 This section describes how to install the inline network adapter in the WAE-7326 appliance. This section includes the following procedures: • Removing the Cover Installing an Inline Network Adapter • Completing the Installation • Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 18 For proper cooling and airflow, replace the cover before turning on the device. Operating the device for extended periods (over 30 minutes) with the cover removed might damage device components. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals:...
- Page 19 Reinstall the riser card. Make sure that the riser card is fully seated in the riser card connectors on the Step 9 system board. Connect any needed cables to the adapter. Step 10 Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 20 Make sure that cables are not pinched by the server components. Remove the fan guide before you route the cables. Reinstall the fan guide when you complete the cable Note routing. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 21 Step 4 Step 5 Connect all external cables and the power cord to the appliance, and then plug the power cord into a properly grounded electrical outlet. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 22 Lift the cover-release latch (see Figure 15). Lift the cover off the device and set the cover aside. Step 4 Figure 15 Removing the Cover Cover-release latch Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 23 Removing the PCI-X Riser-Card Assembly Access holes Release tabs Determine which expansion slot that you will use for the adapter. You can install the Cisco WAE Inline Step 5 Network Adapter card in slot 1 or slot 2 on the riser-card.
- Page 24 Press down on the assembly. (See Figure 18.) Make sure that the riser-card assembly is fully seated in the riser-card connector on the system board. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 25 Perform any configuration tasks required for the adapter. Step 10 Reinstall the cover. Step 11 For instructions on completing the installation, see the “Completing the Installation” section on page Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 26 Gigabit Ethernet, your WAE inline adapter uses Gigabit Ethernet. Speed and duplex settings are port specific so that two inline ports can negotiate different speeds independently. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals:...
- Page 27 (without a WAE inline network appliance connected between them) by using the following standard cabling rules: When you are directly connecting two network devices that are similar, such as two switches, use a • crossover cable. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
- Page 28 LAN and the WAN sides of the WAE inline appliance. Figure 20 through Figure 22 show which cables to use for the WAE LAN and WAN connections between Fast Ethernet ports. Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
-
Page 29: Installation Scenarios And Cabling Examples For Fast Ethernet Connections
Fast Ethernet: WAN0 (InlinePort 1/0/wan) Cable type: Straight-through Cable type: Crossover Connection: WAE to WAN router B (using InlineGroup 1/1) Fast Ethernet: WAN1 (InlinePort 1/1/wan) Cable type: Crossover Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com... - Page 30 (InlinePort 1/0/wan) to WAE 2 LAN0 (InlinePort 1/0/lan) Cable type: Straight-through Cable type: Crossover Connection: WAE 2 to WAN router Fast Ethernet: WAE 2 WAN0 (InlinePort 1/0/wan) Cable type: Crossover Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...
-
Page 31: Related Documentation
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. - Page 32 Obtaining Documentation, Obtaining Support, and Security Guidelines Installing the Cisco WAE Inline Network Adapter OL-12480-03 Get user manuals: See SafeManuals.com...