Maintenance - Craftsman CMCD750 Instruction Manual

Forward/Reverse Control Button (Fig. A)

CAUTION: Before changing the position of the control
button, be sure the trigger is released.
A forward/reverse control button
of the chuck and also serves as a lock-off button.
1. To select forward rotation, release the variable speed
paddle switch and depress the for ward/re verse control
button on the right side of the tool.
2. To select reverse, release the variable speed paddle
switch and depress the forward/reverse control button
on the left side of the tool.
3. The center position of the control button locks the tool in
the off position.
nOTE: Keep the button in the center locked position when
the tool is not in use or when being transported.
nOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click upon start up. This
is normal and does not indicate a problem.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (high torque setting), turn the tool off
and permit it to stop. Slide the speed selector
(towards from the chuck).
2. To select speed 2 (high speed setting), turn the tool off
and permit it to stop. Slide the speed selector back (away
the chuck).
3. If the tool does not change speeds, confirm that the
speed selection switch is completely engaged in the
forward or back position.
MAXiMUM RECOMMEnDED CAPACiTiEs
Metal drilling
Wood, flat boring
Hole saws
Worklight (Fig. A)
There is a worklight 4 located between the chuck
variable speed paddle switch
when the variable speed paddle switch is depressed, and
will automatically turn off 20 seconds after the trigger switch
is released. If the trigger switch remains depressed, the
worklight will remain on.
nOTE: The worklight is for lighting the immediate work
surface and is not intended to be used as a flashlight.
Drill Operation (Fig. A)

WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back‑up" block to prevent damage to the material.
1. Select the desired speed/torque range using the
speed selector to match the speed and torque to the
planned operation.
2 determines the rotation
3 forward
SPEED 1 SPEED 2
1/4" (6.35 mm) 1/8" (3.2 mm)
3/4" (19 mm) 1/2" (12.7 mm)
3/4" (19 mm) 5/8" (15.9 mm)
5
1 . The worklight is activated
2. For WOOD, use twist bits, spade bits, power auger bits
or hole saws. For METAL, use high-speed steel twist drill
bits or hole saws. Use a cutting lubricant when drilling
metals. The exceptions are cast iron and brass which
should be drilled dry.
3. Always apply pressure in a straight line with the bit. Use
enough pressure to keep the drill bit biting, but do not
push hard enough to stall the motor or deflect the bit.
4. Hold tool firmly with both hands to control the twisting
action of the drill.
5. iF DRill sTAlls, it is usually because it is being
overloaded. RElEAsE TRiggER iMMEDiATElY, remove
drill bit from work, and determine cause of stalling. DO
nOT CliCK TRiggER OFF AnD On in An ATTEMPT
TO sTART A sTAllED DRill – This CAn DAMAgE
ThE DRill.
6. Keep the motor running when pulling the bit back out of
a drilled hole. This will help prevent jamming.
Screwdriver Operation (Fig. A)
1. Select the desired speed/torque range using the speed
selector 3
planned operation.
2. Insert the desired fastener accessory into the chuck as
you would any drill bit.

MAINTENANCE


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
and the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1‑888‑331‑4569.
to match the speed and torque of the
English
9