Advertisement
Quick Links
INSTRUCTION SHEET
#346307
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING CARRIER FOR ANY DAMAGE.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
Thank you for your purchase. Before assembly, read this instruction manual carefully.
After reading, be sure to store this instruction in a safe place, should it be needed for future reference.
5/16-18 set screw
(quantity of 4)
Step 1 - Assemble crossbracing.
• Tighten set screws*.
1a
set *
screw
Step 2 - Attach crossbracing to legs.
• On legs, measure and mark desired height** of crossbracing.
• Insert leg through casting, stop at the mark you made.
Repeat on remaining legs and castings.
• Snug the set screws*.
2a
set screw*
2b
Eagle Foodservice Equipment, Eagle MHC, and SpecFAB
Spec-Bar
ASSEMBLY INSTRUCTIONS
SAVE YOUR BOX AND ALL PACKING MATERIALS.
Hardware:
#8-18x1/2" screw
(quantity of 9)
1b
1a
casting
threaded hole
in casting for
crossbracing
* To meet NSF standards:
Set screws must be filled
with NSF-approved sealant.
casting
threaded hole
in casting for
legs
2a
corner casting
* To meet NSF standards:
threaded hole
in casting for
Set screws must be filled
legs
with NSF-approved sealant.
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A.
• Phone: 302/653-3000 • 800/441-8440 • Fax: 302/653-2065
• www.eaglegrp.com • www.eaglegrpnews.com • www.eaglemhc.com
Units
®
CAUTION
Tools required:
• Drill
• 1/8" Drill bit
• 5/32" Allen wrench (provided)
• Phillips screwdriver
• Common screwdriver
• Clamps
1b
1a
2b
2a
are divisions of Eagle Group. ©2022 by the Eagle Group
®
1b
corner casting
threaded holes
in casting for
crossbracing
set screws*
2b
** To meet NSF standards:
6˝
Attach crossbracing at least
6˝ from the floor to the
bottom of crossbracing.
(continued on next page)
EG10024
Revised 10/22
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Eagle Group Spec-Bar
Summary of Contents for Eagle Group Spec-Bar
- Page 1 • 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • Phone: 302/653-3000 • 800/441-8440 • Fax: 302/653-2065 • www.eaglegrp.com • www.eaglegrpnews.com • www.eaglemhc.com Eagle Foodservice Equipment, Eagle MHC, and SpecFAB are divisions of Eagle Group. ©2022 by the Eagle Group ®...
- Page 2 Spec-Bar Units ® ASSEMBLY INSTRUCTIONS BEFORE CONTINUING… If joining two or more units together, skip to page 3. Step 3 - Assemble legs to underbar unit. • Insert leg into each • Tighten gusset of underbar unit. set screws* (one located at each gusset).
- Page 3 Spec-Bar Units ® ASSEMBLY INSTRUCTIONS If joining two or more units together, continue assembly by following these instructions… channels bottom mounting Step 3 - Attach bottom mounting plate. clip drive • Carefully lay units onto their rear side on the floor, screws side-by-side.
- Page 4 ( End ) LIMITED WARRANTY Metal Masters Foodservice Equipment Co Inc. d/b/a Eagle Group or Eagle Foodservice Equipment (“Eagle”) hereby warrants to you, the original purchaser and end-user (“you” or “your”), that the products manufactured by Eagle that you purchased which accompany this Limited Warranty (“products”) shall be free from defects in materials and workmanship under normal use consistent...
Need help?
Do you have a question about the Spec-Bar and is the answer not in the manual?
Questions and answers