Table of Contents
Advertisement
Parts needed
Home power supply cable
1 - ½" (12.7 mm) UL listed or CSA approved strain relief
3 UL listed wire connectors
1 wall or roof cap
Metal vent system
Blower motor system - internal or external (see "Blower
Motor System" in the "Accessories" section.)
Parts supplied
Remove parts from packages. Check that all parts are included.
2 metal grease filters for 30" (76.2 cm) and 36" (91.4 cm)
models
3 metal grease filters for 48" (121.9 cm) models
Range hood canopy with LED lamps installed.
1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct
transition with damper
Wood support
Grease drip trays
4 - 6 x 80 mm mounting screws
4 - 3.5 x 9.5 mm screws
6 - 4.2 x 19 mm screws
2 - D5.3 x 20 mm washers
2 - 10 x 50 mm wall anchors
T-20 TORX
adapter
®†
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the range hood on the rear wall of the
range hood.
Canopy range hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions provide minimum clearance.
The canopy range hood is factory set for venting through the roof
or through the wall.
All openings in ceiling and wall where canopy range hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
†®TORX is a registered trademark of Saturn Fasteners, Inc.
4
Product Dimensions
Front view
3³⁄ "
(8.1 cm)
30" (76.2 cm)
36" (91.4 cm)
48" (121.9 cm)
Back view
A
9 ⁄ "
(24.4 cm)
18¹³⁄ " (47.8 cm) for 48" (121.9 cm) Hood
12¹³⁄ " (32.5 cm) for 36" (91.4 cm) Hood
9¹³⁄ " (24.9 cm) for 30" (76.2 cm) Hood
A. Knockout into terminal box
B. Top of hood
C. Wood support
D. Bottom of hood
Optional Full-Width Duct Cover Installations
12"
(30.5 cm)
12"
(30.5 cm)
18"
(45.7 cm)
A. Optional full-width duct cover
B. Range hood
18¹⁄ " (45.9 cm) for 48" (121.9 cm) Hood
12¹⁄ " (30.6 cm) for 36" (91.4 cm) Hood
9¹⁄ " (23.0 cm) for 30" (76.2 cm) Hood
CL
6¹⁄ " (16.5 cm)
12" (30.5 cm)
18" (45.7 cm)
25" (63.5 cm)
B
CL
C
(45.7 cm)
D
18"
A
B
Advertisement
Table of Contents
