Product introduction Thank you for purchasing this Luxibel product. For your own safety, please read the instruction manual carefully before turn on the product for the first time. Before unpacking the fixture, please make sure that the packaging is in good condition and that following items will be found in the box: •...
Page 4
Safety Notes Each person which is responsible for the installation, the usage of service of this unit must be qualified and has to follow the instruction in this manual. Be careful when using the device. You risk an electrical shock from high voltage, if you touch the wires! The device has left our company in manufactured proofed state.
Page 5
measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help.
The device can only run with 100-240V voltage, 50/60 Hz power, don’t connect to any other wrong power. Disconnect the device from main power before open the shield or maintenance. The device is designed only for indoor usage, please keep it away from moisture.
Page 7
Trouble shooting Problems Possible reasons Solutions Device not Powercon or power cable Change a good power cable to try damaged power up Faulty power supply Replace new power supply LED off Temperature protection Check the temperature from menu Fan not working Check the fan speed info from menu Faulty LED Replace new LED...
Installation There are specific regulations like BGV C1 (old VBG 70) or country related regulations which need to attend during the installation. The installation has to be handled by skilled persons only! Suspension device hast to be built and calculated in order to handle up to 10 times its specific load limit over a time of one hour without permanent or harmful deformation.
Page 9
Installation of the B EXPO500ATW The device could be either put on a solid and even surface, or mounted upside down or sideways like left picture. The mounting place must be sufficient stable and be able to support a weight of 10 times of the unit’s weight.
Control Menu Menu tree Default settings shadowed. MODEL NAME:B EXPO500ATW DMX Addr① DMX mode① 8CH / / 12CH Max Temp① 80~130℃/176~266℉ (85℃) Dimmer DimmerFine Zoom Power Mode Strobe Lamp Temp FAN1: XXXR Fan Speed FAN2:XXXR FAN3: XXXR Soft version Temper. C/F①...
Page 12
DMX Mode DMX addressing The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has four channel modes: 20/21/15/17, if we set the mode at standard 18 channels mode, and there are several models need to be independently controlled, we just simply address first fixture at 1, and second fixture at 21, third one at 41, etc.
Page 13
DMX Chart Channel name function Min DMX Max DMX 8CH 9CH 12CH Main Dimmer 0->100% DimmerFine 0->100% 2800K - 6000K Zoom Small angle -> Big angle Tilt TiltFine PanFine Strobe open Strobe effect slow to fast Strobe Random strobe effect slow to fast No function Auto...
Page 14
has a unique RDM code before left factory to distinguish from each other, usually not suggest users change this code freely. Software upgrade function via DMX cable, if there is any new firmware for this device come out, it can be upgraded simply via a software upgrade box, no need to change any mechanical parts.
Technical Specifications Dimensions drawing Physical Dimensions (WxHxD): 36,2 x 32 x 46.8 cm | 14,3” x 12,6” x 18,4” Packaging dimensions (WxHxD): 43.9 x 386 x 51.1 cm | 17.3” x 15,2” x 20,1” Net weight: 11 kg | 24,3 lbs Gross weight: 12 kg | 26,5 lbs Mounting options Hanging: 3x M12 hole...