Table of Contents
Advertisement
- CD Player Flow Chart
[Key]
[4] + [6] + RESET
Test Mode In
Contents
Display
[CD] or [SOURCE]
Source CD
MIN
SEC
**
[SCAN/RPT]
Power ON
(T.OFFSET adjustment required)
MIN
SEC
00
[SCAN/RPT]
[3]
Power Off
Focus Close/S-curve/
F, F0 Measurement
MIN
SEC
MIN
SEC
91
[SCAN/RPT]
[1]
Power Off
Tracking Close
(AGC, Applicable Servo)
MIN
SEC
MIN
SEC
XX
XX
[1]
[SCAN/RPT]
Power Off
AGC/F.BIAS
Display Switching
MIN
SEC
MIN
SEC
??
??
[SCAN/RPT]
Power Off
MIN
SEC
Switching must take place in the following sequence.
*1) Switching must take place in the following sequence.
→
Focus Close
S.Curve Check
MIN SEC
MIN SEC
00
00
01
01
MIN SEC
(
)
99
99
*2)
Single TR /4TR / 10TR / 32TR / 100TR
*3) Switching must take place in the following sequence.
→
→
→
Single TR
4 TR
10 TR
92(82)
93(83)
9X(8X):91(81)
*4)
It applies to the CRG Move and 100TR Jump alone.
*5) Switching must take place in the following sequence.
→
Min/Sec (or Track No.)
F.AGC Gain
(AGC Gain = (Current value/Initial value) x 20)
*6) Switching must take place in the following sequence.
→
→
F.Cancel Display
T.Offset Display
(F.Bias value, F.Cancel value, T.Offset value, T.Bal value
= (Upper 8 bits of the setting (7F[H] to 80[H] + 128)/4
= 63[D] to 32[D] to 00[D]).
•
Operation of TR JUMPs other than 100TR is continued after your finger has left the key.
CRG Move and 100TR Jump are forced to the Tracking Close Mode when the key is released.
•
Powering on or off resets the Jump Mode to the Single TR (91).
•
When ending the test mode, apply the reset (the reset is applied in two minutes from powering off).
Note:
The commander for G1 mech. must be employed for controlling the test mode.
Note:
Sound is unavailable even after the tracking has been closed
(this trouble results when the IC for the STS is not controlled in the test mode).
Note:
When you pressed the [SEEK/SKIP+] or [SEEK/SKIP-] key during the Focus Search, you must turn the power off immediately
(otherwise, the lens can stick resulting in actuator damages).
**
[3]
Power ON
(T.OFFSET adjustment not required)
MIN
SEC
00
99
99
[5]
*1
Tracking Servo
Focus Mode Select
Close
SEC
MIN
MIN
00
91
0X
0X
or
MIN
99
[5]
Tracking Close
(No AGC, Applicable Servo)
MIN
SEC
XX
XX
[3]
CRG/TR Jump Count
*5
AGC
Select
MIN
SEC
MIN
XX
XX
XX
→
Focus EQ Measurement.
MIN SEC
02
02
→
→
CRG Move
32 TR
100 TR
94(84)
95(85)
96(86)
→
→
T.AGC Gain
F. BIAS Setting
→
T.Bal Display
Rough Servo.
FX-MG6096ZH,FX-MG6096ZH2
[SEEK/SKIP+]
[1]
CRG+
SEC
MIN
SEC
00
00
00
or
SEC
TRK
MIN
99
99
99
[3]
[SEEK/SKIP+]
Auto Adjustment Display
*6
CRG+
/Rough Servo
MIN
SEC
MIN
SEC
8X
??
??
or
MIN
SEC
9X
[5]
[SEEK/SKIP+]
*2
CRG–/TR Jump–
CRG+/TR Jump+
*3
SEC
MIN
SEC
MIN
XX
XX
XX
MIN
or
MIN
[Key]
[SCAN/RPT]
Power ON/OFF
CRG+/TR Jump+
[SEEK/SKIP+]
(Toward outer perimeter)
CRG-/TR Jump-
[SEEK/SKIP-]
(Toward inner perimeter)
Tracking Close/AGC gain,
[1]
F.Bias adjustment value display switching
Auto Tracking Balance adjustment/
[2]
Tracking Open
[3]
Focus Close, S.Curve, F.EQ measurement/
Rough Servo/AGC
[4]
Focus Open
Focus Mode select/Tracking Close/
[5]
CRG*TR Jump Switching
[6]
DISC UP
[EJECT]
DISC Eject
[LOAD]
DISC Load
[1]
Mechanism Test Mode
New Test Mode
Initial State
SEC
MIN
0*
**
RPT
[SEEK/SKIP-]
CRG-
MIN
SEC
00
00
or
MIN
SEC
99
99
[SEEK/SKIP-]
Tracking Balance
CRG-
Adjustment
MIN
SEC
MIN
8X
8X
8X
or
MIN
SEC
9X
9X
9X
[SEEK/SKIP-]
[2]
*2
Trackig Open
SEC
MIN
SEC
8X
8X
XX
XX
or
MIN
SEC
9X
9X
*4
[2]
Trackig Open
SEC
8X
8X
SEC
9X
9X
Operation
Test Mode
New Test Mode
Error occurrence time/
Cause display switching
Track+/FF
Track-/REV
Mode
RAMDOM
Auto/Manual switching
DISC UP
DISC Eject
DISC Load
[5]
[2]
SEC
8X
8X
[4]
SPINDLE
Uniform/
Double Switching
MIN
SEC
XX
XX
69
Advertisement
Table of Contents
