Table of Contents
Advertisement
Quick Links
SPP-1000-4WC
Introduction
SMART+ PRODUCTS Infrared Heaters utilize the latest infrared heat technology. smart+ products
Infrared Heaters provide a safe, convenient, clean, and economical way to distribute heat
throughout your home or business without producing deadly fumes or monoxide gases. Our
heating system produces therapeutic infrared heat that can potentially relieve symptoms of
cardiovascular conditions and inflammatory diseases. Infrared heat technology, in general,
produces rays that are safe and highly beneficial to our bodies and health professionals have been
using infrared technology for decades to treat muscle and joint pains.
smart+ products Infrared Heaters are constructed of a wood housing. They are equipped with
nylon caster wheels for easy mobility. And the highly efficient filter can be maintained and cleaned
by simply rinsing with warm water.
Safety
USE CAUTION
Save these instructions because electrical safety is essential to keeping your home safe. When
using an electrical appliance, basic precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons. Please adhere to the following safety instructions:
The heater must be operated by an adult. Keep heater out of the reach of children.
Only operate the heater when it is on the floor.
Do not operate heater near any water.
Do not plug heater into any other cord connected device such as power strip, surge
protector, multiple outlet adapter, grounding adapter, outlet-type air fresheners or extension
IMPORTANT INSTRUCTIONS
1
Advertisement
Table of Contents
Related Manuals for Smart+ Products SPP-1000-4WC
Summary of Contents for Smart+ Products SPP-1000-4WC
- Page 1 Infrared Heaters are constructed of a wood housing. They are equipped with nylon caster wheels for easy mobility. And the highly efficient filter can be maintained and cleaned by simply rinsing with warm water.
-
Page 2: Heater Specifications
Use heater only as described in this manual. Any other use is not recommended by the manufacturer as it may lead to fire, electric shock, and/or series physical injury or death. Heater Specifications SMART+ PRODUCTS Heater Model# SPP-1000-4WC Carton Size: 19.4 in x 17.1 in x 18.6 in Thermostat: Electronic Analog Heater Size: 15.8 in x 14.8 in x 16.2 in... -
Page 3: How It Works
1000 square feet depending on the ambient temperature. And it does all this with a noise level below 46db. The smart+ products Infrared Heater is not for use as the primary/sole heating system. - Page 4 1. First, check the carton to make sure there are no obvious damages that may have occurred during shipment. 2. Open the smart+ products Infrared Heater packaging and remove the heater by sliding it from the box. You may want to gently and cautiously turn the entire box upside down letting the heater slowly slide out.
- Page 5 (Note: If the current ambient temperature is greater than the set temperature, the HI/LOW display, fan, and Quartz Bulbs will not operate.) 2) By pressing the F/Down button, you can switch the temperature format from Fahrenheit to Celsius and vice versa. Press the F/Down to switch from Fahrenheit...
- Page 6 5 seconds later the value switches to ambient temperature 4) Again, the default set temperature displayed on the LED display is 72 F. By pressing the TEMP button, the LED display will switch to the temperature status and flash. You must press the HI/LOW/UP button or F/DOWN button once again within (5) seconds to set the desired temperature.
- Page 7 (Note: To set back to factory settings, hold down the TIME button for (5) seconds. This will set all values back to default.) 7) The smart+ products Infrared Heater can be turned off by pressing the POWER button. DO NOT TURN OFF THE MASTER POWER SWITCH ON THE REAR OF THE HEATER OR UNPLUG THE HEATER UNTIL THE FAN SHUTS DOWN.
-
Page 8: Care, Maintenance, And Storage
4. Existing HVAC heating system vents should be closed. This allows the heater to function in an isolated area. 5. It is not recommended to operate heater in areas exposed to non-insulated concrete or metal walls. Concrete floors should be covered to insulate the heat within the room. If the heater filters become dirty or dusty, they must be cleaned for the heater to operate at its maximum efficiently. - Page 9 2. PROBLEM: a. The amount of heated air exiting the front of the portable heater is reduced. SOLUTION: Check the electrostatic filter to make sure it is free of dust and dirt. Also check the front grill and rear air intake to make sure it is not being blocked by any kind of debris.
Need help?
Do you have a question about the SPP-1000-4WC and is the answer not in the manual?
Questions and answers