Advertisement

Quick Links

Bedienungsanleitung
User manual
Content not included

Advertisement

Table of Contents
loading

Summary of Contents for Respekta Amadeo WKS171-19

  • Page 1 Bedienungsanleitung User manual Content not included...
  • Page 16 a. Lösen Sie die 3 in der Abbildung markierten Schrauben der LED-Lampenabdeckung oben auf der oberen Zone und entfernen Sie den LED- Lichtstecker. b. Lösen Sie die vier in der Abbildung markierten Schrauben, mit denen die LED-Platine befestigt ist, ersetzen Sie die defekte LED Lampe und installieren Sie LD-Platine wieder.
  • Page 19 Content fi220910atNEG Wine cooler WKS171-19 We recommend that you read these operating instructions carefully. This will enable you to become better and more quickly familiar with your new appliance. Mark those parts, which are of special importance to you. Keep this document to hands so that you can refer to it at any time and pass it on to any subsequent owners.
  • Page 20: Safety Instructions And Warnings

    Safety instructions & warnings Your safety is of the utmost importance to our company. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Technical Department.
  • Page 21 Do not allow child reach into compressor compartment or touch metal components at rear of the appliance in case of possible injury. Keep away from water Do not spray water on the appliance or wash the appliance by pouring or filling water in case of invalid insulation and possible electric shock.
  • Page 22: Installation

    Installation Position Do not lean the appliance over 45°when moving it to position. The appliance must be put on flat, firm & dry floor or similar non-combustible pad; do not use the package foam pad. Do not put the appliance in the wet place. Do not use the appliance in the frozen place.
  • Page 23: Description Of The Appliance

    Description of the appliance Overall image 11. Upper hinge 1. Housing 12. Hygrometer 2. Shelf 10. Door seal 3. Cover board 9. Handle Control panel 5. Fan 8. Door 6. Adjustable foot 7. Lower hinge Note: Shelves, doorframe, handle and other accessories could be different according to different models and configuration.
  • Page 24: Handle Installation

    Handle installation Install handle to the doorframe of the appliance. The handle is delivered in a separated package with screws together inside the carton. 1. Reveal two small holes on the doorframe from inner side by pulling out a bit the door seal 2.
  • Page 25: Operation

    Turn the door 180 degrees upside down and fit the top door axis hole to the top left hinge and put lower hinge plate on the lower hinge and keep the door steady to screw the lower hinge plate with the left bottom door frame. [Figure 4] Door reversing is finished.
  • Page 28: Wine Storage

    Wine storage The appliance equip with independent shelves to allow your collection of wine get mature quietly and peacefully. 14 wood shelves loading capacity: 171 bottles. (standard Bordeaux with 750ml ) Loading capacity will vary in terms of different way of bottle arrangement or different bottle sizes.
  • Page 29: Troubleshooting

    Troubleshooting The appliance makes lots Please adjust the front foot, keep the appliance of noise? leveling. Please keep the appliance a bit space from walls. Liquid flowing sound It is normal because of the refrigerant working inside the cabinet? inside. The appliance does not Make sure the appliance is connected to the power start?
  • Page 30: Power Cut

    The below items will damage the surface of wine cooler: Power cut Most power cuts could be resolved within a short time. To protect your wines during a power cut, avoid opening the door as much as possible. During very long power cuts, take the necessary measures to protect your wine.
  • Page 31 Unscrew the 3 screws marked in the picture of the LED lamp cover on top of the upper zone and remove the LED light plug. Unscrew the four screws that secure the LED board, marked in the picture, replace the defective LED lamp and reinstall the LED board.

Table of Contents