Advertisement
Quick Links
Thank you for purchasing our Brake Bleeder Set.
Please read this Instruction Manual to use this product safely and properly.
Please fully understand handling cautions and method of use before actual use.
Also please keep this Instruction Manual together with the product.
This product is special equipment for injecting brake fluid by pressure sending.
This product is equipment driven by compressed air from compressor.
There are 2 types of handling precautions as follows;
CAUTION
： Failure to heed instructions could lead to human injury
ordamage to equipment.
NOTE
：Important information on use and maintenace of the product.
ABX70
Brake Bleeder
INSTRUCTION MANUAL
1
Advertisement
Related Manuals for KTC ABX70
Summary of Contents for KTC ABX70
- Page 1 ABX70 Brake Bleeder INSTRUCTION MANUAL Thank you for purchasing our Brake Bleeder Set. Please read this Instruction Manual to use this product safely and properly. Please fully understand handling cautions and method of use before actual use. Also please keep this Instruction Manual together with the product.
- Page 2 INDEX 1．EACH PART …………………………………………..… 2．SPECIAL FEATURE …………………………………..3．CONTENTS ……………………………………………..4．SPECIFICATION ………………………………………... 5．APPLICATION …………………………………………... 6．CAUTIONS ……………………………………………….. 7．HOW TO USE ①．INJECTING BRAKE FLUID …………………..….. ②．SELLECTING ATTACHMENT ………………...… ③．INSTALLING ATTACHMENT TO RESE ………………………………………………..…………………………………………………. 9-10 ………………………………. B1 or B2 + D1 11-12 ………………………………... B1 or B2 + E1 ④．HOW TO OPERATE ……………………………….
- Page 3 1. PART ① ．BODY ② . ATTACHMENT...
- Page 4 2. SPECIAL FEATURE ① Shorter operation time by continuous pressure sending. ② Applicable for many car models by using 4 attachments. ③ High quality compact design. ④ Easy to use Air Pressure Sending Type. ⑤ One touch installing Plate Rubber (Attachment A1) ⑥...
- Page 5 6. CAUTIONS ON USE Before use, read the following cautions & notes and check all items. CAUTION This product can be used qualified persons only such as automotive mechanics or persons with license. Do not use for any other purpose than sending brake fluid. ...
- Page 6 7. HOW TO USE ①．Injecting brake fluid Injecting full capacity（Max. 2 litres） ※ If not full capacity, please apply a different method（Please refer to P15） (1).Turn Switch Lever from Neutral (中立) to Discharge (排気), open Cap and inject brake fluid. until it comes to Filter Position (Full Capacity = 2 litres). NOTE ・Do injecting operation on a level surface.
- Page 7 ②．Selecting Attachment ※ Regarding the reservoir guard, there are 3 types (5 kinds). So please select the suitable Attachment by checking shapes of the reservoir and the guard, inner diameter of diaphragm, surroundings of the master cylinder and referring to Application Chart. a) Flange Type（3 kinds）...
- Page 8 ③ ．Installing Attachments to Reservoir Select the suitable Attachment by checking shapes of the reservoir and guard, inner diameter of diaphragm, surroundings of the master cylinder and referring to Application Chart. NOTE ・After installing on the reservoir, do not give any external force on Attachments. Otherwise, it may give damage to the reservoir or cause brake fluid leak.
- Page 9 [ How to use attachment A2 ] (1) Remove the cap and strainer of the reservoir. Turn Adj. Nut clockwise close to the bore of the reservoir port and pooch Expansion Rubber. NOTE ･Do not forget to pooch Expansion Rubber, otherwise it may contact the separator and cannot be used properly.
- Page 10 (4) Turn Lock Nut counter-clockwise. After Plate contact the guard, turn Lock Nut one time or so to fix Attachment on the reservoir by Plate and Claw. If the reservoir is old or changed in its shape, install A2 and then Put Clamp E1 as the above, and put the chain on the master cylinder body.
- Page 11 (3) Put Clamp D1 on Lock Nut of B1 or B2 making the master cylinder and Claw at right angle. Fit Shaft in Inner Groove (B1) or Outer Groove (B2) and take the balance of left and right Claw and hitch Claw on the guard. Turn Lock Nut counter-clockwise until locked to fix Attachment on the reservoir by Plate and Claw.
- Page 12 [ HOW TO USE ATTACHMENT B1 or B2+ CLAMP E1 ] ※ Put E1 on B1 or B2 for use. Installing method for B1,B2 is same as in the above case of B1 orB2+D1. NOTE ･For car models which reservoir is positined offset to the master cylinder (Mitsubishi), please use D1.
- Page 13 ④ OPERATION (1) After installing Attachment, connect Socket Coupler on the end of Pressure-Sending Hose with Plug Coupler of Attachment. NOTE ･Connect Couplers just straight. If inserted with angle, Coupler will be locked and cannot be connected. ･Check Couplers are connected securely by pulling Socket Coupler lightly. If not fully connected, brake fluid may scatter when sending it.
- Page 14 (3) Turn Swith Lever to Pressure-sending (圧送) and start pressure-sending brake fluid. After checking there is no leak from Attachment, Change brake fluid and removing air by operating Bleeders such as caliper, wheel cylinder, etc. NOTE ･ If blur or leak of brake fluid occurred due to improper installment of Attachment, turn Switch Lever to Discharge(排気)and remove the remaining air, and install Attachment again.
- Page 15 ⑤ REMAINING AMOUNT INDICATION When the level of brake fluid in Tank becoms below1, the edge of Piston can be seen at the window for remaining amount indication. Gauge on Indicator(the window of remaining amount indication) is graduated at 0.2. NOTE ･Indicator(the window for remaining amount indication shows the remaining brake fluid to be pressure-sending.
- Page 16 ･Pressure-Sending Hose and Plate Rubber & Expansion Rubber of Attachment will be consumed. So when the deterioration such as cracking on surface is noticed, change with spare parts. 9. SPARE PARTS Description Item No. Attachment A1 ABX70-A1 Attachment A2 ABX70-A2 Attachment B1 ABX70-B1 Attachment B2 ABX70-B2...
- Page 17 APPLICATION CHART FOR ATTACHMENT & CLAMP Car Maker Car Model Inner Dia. Attachment +Clamp Φ23 TOYOTA Trucks and One-Box cars such High Ace, Light Ace, Town Ac etc. Φ42.5 Passenger cars such as Crown, Corona,Camry, Corolla, Prado, e Φ57 Old models B1 + D1 Φ70 B2 + D1...
- Page 18 Φ34 FUJI Domingo, etc. Legacy, etc. Φ60 REX, etc. B1 + D1 Φ67 Old models B2 + D1 Φ34 ISUZU Φ42.5 Φ54 Big Hone, etc. B1 + D1 [MERUCEDES] all models [BMW] 3 & 5 series [OPEL] Astra, Vita [GM] Cadilac...
Need help?
Do you have a question about the ABX70 and is the answer not in the manual?
Questions and answers