Cleaning And Care - AEG EC6-1 Series Instruction Book

Make espresso co ee
5
Put one-cup filter cup into filter holder. Add one spoon of ground coffee, press it tight with tamper; or
add an E.S.E pod and put it into filter cup. E.S.E (Easy Serving Espresso) Pods can be used to simplify
the espresso preparation. Each pre-packed pod contains 7 grams of coffee, already measured and
pressed and sealed between 2 ne layers of lter paper.
6 Fix the filter holder onto brewing head anti-clockwise from "LOCK" to "CLOSE" position.
7
Put a warm cup on the drip tray. In "pre-heating done" mode when
steadily and fully light on, press
8
Wait a moment and the top-grade coffee will ow out. When the machine stops working, your coffee is
now ready.
9
Now apply two-cup filter cup. Press
10
NOTE: If both and
cancel brewing, or (step 11)
11
(step 10) you may restart brewing after cooling down the boiler. Turning the knob to
and release hot water from steam nozzle. The pump stops working automatically when it's done cool-
ing off. Turn the knob off and resume brewing again.
Make hot water
12
In "pre-heating done" mode when
knob to position. Hot water comes out of the steam nozzle. Turn the knob off when the desired
amount is complete.
Froth milk and make cappuccino/latte
13
Fill a jug with 100ml (for cappuccino) or 200ml (for latte) milk. NOTE: make sure jug diameter is no less
than 70±5mm, and jug capacity can hold twice the milk volume after it's done frothing.
14
In "pre-heating done" mode when
button, it starts blinking. NOTE: Use full milk at refrigerator temperature (NOT HOT!).
15
When the button stops blinking, steam / milk frothing function is ready. Before frothing milk, push
steam nozzle in the direction of drip tray, turn the knob to
no water coming out, then turn off steam function by turning the knob back to horizontal "OFF" position.
16
Immerse steam nozzle in milk about 2cm under the milk surface, turn on the knob. Make sure the steam
nozzle is placed in a position that makes the milk turning in one direction inside the jug from top to
bottom.
17
When the desired level of foam is reached, turn off the knob. NOTE: Clean steam nozzle with wet
sponge immediately after steam stops generating, but care not to hurt! The pump automatically
stops working after milk frothing for 3 minutes.
18
Pour the frothed milk into the espresso prepared, now the cappuccino/latte is ready. Sweeten to taste
and if desired, sprinkle the froth with a little cocoa powder. NOTE: After making steam, you may imme-
diately make espresso again by pressing
quickly, cool down the boiler and resume brewing (see step 11).
DIY / volume
19
In "pre-heating done" mode when
/ button for 3 seconds to start resetting mode. Press
again to stop when the desired volume (25-55ml/55-105ml) is complete. Now the volume is saved for
next operation and from then on.
20 Restore factory volume setting simply by long pressing

CLEANING AND CARE

21
Turn the machine off and unplug the power cord. Let the machine cool down completely before clean-
ing. Wipe all outer surfaces with a damp cloth. Clean water tank, drip tray and drip grid regularly. Never
use caustic or abrasive cleaners, and never immerse the machine in liquid!
8
button to start brewing process.
button. Brew 2 cups of espresso at the same time.
buttons start blinking quickly, you may simply press
and and
and and
or
and and
and
buttons are steadily and fully light on, turn the
buttons are steadily and fully light on, press
position and release steam until there's
button. If both and
buttons are steadily and fully light on, long press
/ button to start brewing and press
and buttons for 3 seconds again.
and buttons are
or button to
position
buttons start blinking
www.aeg.com