Subscribe to Our Youtube Channel
Related Manuals for McIntosh MDA200
Summary of Contents for McIntosh MDA200
- Page 1 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com MDA200 D/A Converter Owner’s Manual...
-
Page 2: Table Of Contents
2 channel PCM Binghamton, New York 13903 Using Your MDA200 �� �� �� �� �� �� �� �� �� ��12 (Pulse Code Modulation), Dolby Digital and DTS Remote Control �� �� �� �� �� �� �� �� �� �� �� ��13... -
Page 3: Performance Features
• Gold Plated Connectors sources or use the MDA200 as the preamplifier The terms HDMI, HDMI High-Definition together with McIntosh source components and The input and output connector contacts are gold Multimedia Interface, and the HDMI power amplifier to form a complete audio system. -
Page 4: Front Panel Displays And Switches
2� IR Sensor receives commands from your remote control. 3� Standby Indicator LED illuminates when the MDA200 is connected to AC power. 4� ADJUST Knob adjusts the output level when “Adjustable” is selected in the setup menu. Also used to navigate in the... -
Page 5: Rear Panel Connections And Switches
3.5mm connectivity. signal. stereo mini phone plug cable. Note: The HDMI ARC functionality of the MDA200 is only 9� DA2 DIGITAL AUDIO MODULE 4� IR INput connects to an IR receiver using compatible with ARC TVs. Other devices like DVD 10�... -
Page 6: Connectors And Cable Information
Connectors and Cable Information XLR Connectors USB Audio Service USB Port The USB audio input of the MDA200 provides Below is the pin configuration for the XLR bal- The service USB port on the rear the capability to receive music/sound in a digital anced output connectors on the MDA200. -
Page 7: System Configurations
Shown below are two different system configurations. Your system may vary from this, however the Setup Menu Notes: actual components would be connected in a similar manner. Level Adjust Fixed (default) Note: The preamplifier or power amplifier may be connected to the MDA200 balanced or unbalanced outputs. Front IR Disabled REMOTE Power IR... - Page 8 Exiting/Navigating Back: technicians. 1&2) A brief deliberate press (not hold) and release of The version of the main firmware of the MDA200 DATA PORT All Data / Individual Input the INPUT knob will exit the current menu. Make can be viewed by entering the setup menu. The...
-
Page 9: Setup Menu
CEC. Select the adjustable setting when using the receive the same data from the remote control. MDA200 as both a DAC and a preamplifier, to SETUP: HDMI CEC PWR [ input name ]: Dedicate the data port to a spe- directly feed a power amplifier. -
Page 10: Trim Functions Menu
To correct this, you can raise or lower the To disable power commands coming from the volume of an input as it enters the MDA200 by data port or from a connected external IR sensor adjusting its trim level with this setting. -
Page 11: Dimensions
Dimensions The following dimensions can assist in determining the best location for your MDA200. ” -1/2 44.45 cm ” -7/8 Front View 9.84 cm -11/16” 39.95 cm -3/8” 39.05 cm -5/8” Side View -7/8” 6.66 cm 9.8 cm -1/16” -9/16”... -
Page 12: Using Your Mda200
MDA200 is located adjusted before sound is heard. in a cabinet with the doors closed. • When the MDA200 is set to the HDMI input, the unit will automatically turn On and Off with the TV. Powering On / Turning Off: The front display will show “Entering HDMI... -
Page 13: Remote Control
Note: The following additional discrete IR commands for external control systems are available: POWER ON, POWER OFF, INPUT (Down), COAX 1, COAX 2, OPT 1, OPT 2, USB, MCT, and HDMI ARC. Contact McIntosh Technical Assistance or your dealer for more information. -
Page 14: Specifications
0 - 8.0Vrms Unbalanced Standby Power, less than 0.5 watts DSD64, DSD128, DSD256, DSD512 0- 16.0Vrms Balanced Note: Refer to the rear panel of the MDA200 for the correct HDMI: PCM 24-bit, 44.1-192kHz, bitstream voltage. Signal To Noise Ratio (A-Weighted) -
Page 15: Packing Instructions
Customer Service 033836 Inside carton only It is very important that the four plastic feet are Department of McIntosh Laboratory. Refer to 033725 Top pad attached to the bottom of the equipment. This will page 2. - Page 16 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 24120100...
Need help?
Do you have a question about the MDA200 and is the answer not in the manual?
Questions and answers