Advertisement
Quick Links
User's manual
SMD Repairing System INT701A++
90701A++
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.
Advertisement
Related Manuals for WilTec INT701A++
Summary of Contents for WilTec INT701A++
- Page 1 User’s manual SMD Repairing System INT701A++ 90701A++ Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments.
- Page 2 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man- ual, nor in the diagrams and illustrations shown.
- Page 3 You are responsible for the safety of the working zone. • If the cable or plug is damaged due to external influences, the cable must not be repaired, but must be replaced with a new one. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 Place the device on a level and solid surface the temperature of which does not exceed 40 ℃. Place the device horizontally to allow the station to operate correctly. • Connect to mains. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 4 http://www.WilTec.de http://www.aoyue.eu...
-
Page 5: Soldering Iron
Power cord and plug Unsoldering gun with holder Cleaning needle 201242 Soldering-iron holder with tin-solder holder Cover cap (tin-solder not included) Filter spring 20125 Filter 3017J © by WilTec Wildanger Technik GmbH Item 90701A++ Page 5 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de... -
Page 6: Table Of Contents
Large temperature adjustment range • Very short heating periods • Antistatic design (ESD safe) • Useful handle • Holder for soldering iron • Unsoldering gun holder © by WilTec Wildanger Technik GmbH Item 90701A++ Page 6 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de... -
Page 7: Power (W)
Vacuum hose connection of unsoldering On/off switch soldering function iron Control dial for temperature of unsoldering Control dial for temperature of soldering iron iron © by WilTec Wildanger Technik GmbH Item 90701A++ Page 7 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de... -
Page 8: Heating Element Ceramic
Connection cable – Vacuum cable – to connect to to connect to station station © by WilTec Wildanger Technik GmbH Item 90701A++ Page 8 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de... - Page 9 3. Place the unsoldering gun in its holder. Plug the plug into the station, making sure that the marks match. Fasten the plug by turning it clockwise. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 9 http://www.WilTec.de http://www.aoyue.eu 05 2022-1...
- Page 10 Wait until the nozzle has heated up completely before beginning cleaning. c) Clean the nozzle opening with the help of the cleaning needle. d) In case the cleaning needle does not penetrate the opening, instead use the cleaning drill. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 10 http://www.WilTec.de...
- Page 11 The inner part of the nozzle and its surface are coated with a special alloy. If this alloy is damaged by high temperatures, the nozzle is not able any longer to heat up correctly and regularly. Solder © by WilTec Wildanger Technik GmbH Item 90701A++ Page 11 http://www.WilTec.de http://www.aoyue.eu...
- Page 12 5. Securing the filter a) Attach the filter spring to the front holder. b) Attach the front holder to the filter cover, making sure that it is correctly oriented. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 12 http://www.WilTec.de http://www.aoyue.eu...
- Page 13 4. Allow the tip to touch the soldered spot to melt the solder. a) Never touch the board itself with the hot nozzle. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 13 http://www.WilTec.de http://www.aoyue.eu...
- Page 14 Melt the tin-solder. Hold the handle so that the nozzle is exactly above the component to be unsol- dered. Make sure that the nozzle cannot touch the component itself of its contacts. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 14 http://www.WilTec.de...
- Page 15 Soldering: Heat up the component and the line terminals. Clean the board. After the soldering has been finished, you should clean the board and remove all flux agent. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 15 http://www.WilTec.de http://www.aoyue.eu...
- Page 16 Should the values of A and B differ considerably from the ones stated above, replace the plug and heating element or sensor. • If the value measured exceeds 2 Ω, the soldering iron should be cleaned with steel wool or sandpaper (s. Fig.). © by WilTec Wildanger Technik GmbH Item 90701A++ Page 16 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de...
- Page 17 Construction of different types of soldering irons: 900 M/L Align the cable accordingly & choose a convenient bending radius © by WilTec Wildanger Technik GmbH Item 90701A++ Page 17 http://www.WilTec.de http://www.aoyue.eu 05 2022-1...
- Page 18 (913 and 914 types differ from 907 and 908 types in the form of the handle.) № Name № Name Thermal isolation Distancing sleeve Handle Soldering tip Heating element Nipple Quartz crystal glass tube Spring Junction plate 900 S © by WilTec Wildanger Technik GmbH Item 90701A++ Page 18 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de...
- Page 19 The soldering tip temperature is too low. Is the soldering tip oxidised? (See chapter “Care instructions for soldering tips”) The soldering tip temperature could need to be re- calibrated. © by WilTec Wildanger Technik GmbH Item 90701A++ Page 19 http://www.WilTec.de http://www.aoyue.eu 05 2022-1 http://www.teichtip.de...
- Page 20 German law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed- out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the domestic waste.