Advertisement
Quick Links
Operation Manual
Multi-purpose Bending Device
61852, 61899
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps and technical data may deviate insignificantly due to continuous further
developments.
Advertisement
Related Manuals for WilTec 61852
Summary of Contents for WilTec 61852
- Page 1 Operation Manual Multi-purpose Bending Device 61852, 61899 Illustration similar, may vary depending on model Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps and technical data may deviate insignificantly due to continuous further...
- Page 2 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man- ual, nor in the diagrams and illustrations shown.
- Page 3 25.4 (D1~1″) / 31.75 (D1~1¼″) / 38.1 (D1~1½″) / 44.45 (D1~1¾″) Bending forms/moulds (㎜) / 50.8 (D2 ~2″) / 63.5 (D1~2½″) / 76.2 (D3~3″) Bending radius (㎜) 0–2000 © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 Store the device when it is not used. Keep it in a dry, safe location and out of children’s reach. Before storing or re-using the device or tool, check it for damages. © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 4 http://www.WilTec.de...
- Page 5 (2), washers (3, 7), and nuts (8). 6. Place the bow-type lever (15) between the flanges of the bending device and secure it with the long hinge pin (9). © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 5 http://www.WilTec.de...
- Page 6 1. Choose the bending tool matching the radius of the work piece to be bent. Install it as centring tool to the hinge pin (9) fixing the bow-type lever (15) to the bending support (4) (see Fig. 4). Figure 4: Assembly for simple radius bending © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 6 http://www.WilTec.de...
- Page 7 Fig. 6, making sure that the block supporting bolt is mounted as near as possible to the angle bending block. Figure 6: Assembly for simple angle bending © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 7 http://www.WilTec.de...
- Page 8 • Regularly lubricate the mobile parts of the device. • Regularly check the bending device for damaged or used parts. © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 9 26 Bending tool 7.62 cm (3″) Important Note: Reproduction and any commercial use (of parts) of this operating manual, requires a written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 61852, 61899 Page 9 http://www.WilTec.de http://www.aoyue.eu...