Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intelbras TX 8000
Summary of Contents for Intelbras TX 8000
- Page 1 User manual TX 8000...
- Page 2 Congratulations, you have just purchased a product with Intelbras quality and safety. The TX 8000 universal transmitter was developed to facilitate the installation of wired sensors in your daily life, as it allows a wired sensor to communicate wirelessly with the AMT 8000 alarm center. , providing longer battery life. It also has a tamper key to protect against tampering, making your environment even more secure, a key for registration and a status indicator LED.
- Page 3 Care and safety » LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or perform any type of processing of personal data from this product. » This product is intended for indoor environments. » Avoid installing the transmitter directly under metallic surfaces so that there is no change in its operating characteristics.
-
Page 4: Table Of Contents
7.1. Connection between the TX 8000 and the wired sensor ....... -
Page 5: Technical Specifications
1. Technical specifications Operating voltage 3V Lithium battery, model CR2450 Operating current RF range 600 meters without barrier Transmission frequency 915MHz – 928MHz Power 11 dBm Modulation DSSSS BPSK 40 Kbps Compatibility AMT 8000 alarm panel Anti jamming Against invasive signs Anti-violation rear tamper Installation environment... -
Page 6: Product
4. Sensor opening To access the TX 8000 board for registration, battery replacement or to unregister it from the control unit, simply open the lock with the help of a screwdriver and remove its base. This way the board will be exposed and ready for handling. -
Page 7: Enrolling The Tx 8000 Transmitter
Enter 6. Identified the best location for installation The TX 8000 transmitter has signal level indications for communication with the AMT 8000 control panel, this will help you choose the best installation location. follow the procedure: 1. After duly registered, take the sensor to the environment you want to protect;... -
Page 8: Installation
7. Installation The TX 8000 can be secured using double-sided tape or screw. If the option with double-sided tape is chosen, clean the surface that will be in direct contact with the tape and then glue it to the base of the product. If using screws, just open the transmitter and use the holes to pass the screw located on the base of the product, as shown in the following figure. -
Page 9: Configuring The Tx 8000 Transmitter
To close the TX 8000, simply fit the latches and then press the other side for complete closure. Mount the latches Press to lock 8. Configuring the TX 8000 transmitter The adjustment of configurations of the transmitter can be done in two ways, to follow we present or step by step of each one. -
Page 10: Information About Led Operation
» LED Off: with the LED off option, the TX 8000 will only turn the LED on for the first 15 minutes after battery insertion. Factory standard. » LED On: with the LED on option, the TX 8000 will light the LED on every motion detection of the wired sensor connected to it. Configuring the LED through the app After the app is properly connected to the alarm center, select Configure center on the main screen of the app. - Page 11 After selecting the sensor, the following adjustment screen will open. For the XAS 8000 the sensitivity and operating mode settings do not apply. LED configuration only. Sensitivity (not applicable) Level 0 Level 1 Level 2 Level 3 Sensor 1 Always off On when shooting Operating mode (not applicable) Economy mode...
-
Page 12: Battery
Intelbras or directly disposed of in an environmentally appropriate manner, avoiding environmental and health impacts. If you prefer, the battery as well as other unused Intelbras brand electronics can be disposed of at any Green Eletron collection point (electronic waste manager to which we are associated). In case of doubt about the reverse logistics process, please contact us at (48) 2106-0006 or 0800 704 2767 (from Monday to Friday from 8 am to 8 pm and on Saturdays from 8 am to 6 pm) or by e-mail. -
Page 13: Warranty Term
8. After its useful life, the product must be delivered to an authorized Intelbras service center or directly disposed of in an environmentally appropriate manner to avoid environmental and health impacts. If you prefer, the battery, as well as other unused Intelbras brand electronics, can be disposed of at any Green Eletron collection point (waste management facility to which we are associated). - Page 14 Support via e-mail: suporte@intelbras.com.br Customer Service: 0800 7042767 Where to buy? Who installs it? 0800 7245115 Produced by: Intelbras S/A – Indústria de Telecomunicação Eletrônica Brasileira Rodovia BR 459, km 124, 1325 – Distrito Industrial – Santa Rita do Sapucaí/MG – 37540-000 01.22 CNPJ 82.901.000/0016-03 –...
Need help?
Do you have a question about the TX 8000 and is the answer not in the manual?
Questions and answers