AVE VSI-Pro Max Operation Manual page 27

MICROS IDN HARDWARE CONNECTION
The Micros IDN connection use an RS-422 type 4 wire
connection. Therefore the VSI-Pro Max F4 PCB requires
the additional AVE RS-232 to RS-422/RS-485 converter.
The internal jumper settings of the VSI-Pro Max also
need to changed from the default. JP9, JP10, JP11 must
be Off or remove the jumper. See Appendix S, Page 98
for more information on VSI-Pro Max jumper settings.
You will also need to configure the AVE RS-232 to RS-
422/RS-485 converter to be RS-232 to RS-422. See Ap-
pendix J, Page 84 for more information.
AVE also has internal modules that eliminate
this adapter but must be installed at the factory and speci-
fied upon ordering.
MICROS ISN NETWORK
Press the "Up" or "Down" button to move the cursor to
"MICROS ISN NETWORK" and press "Set". The MICROS
ISN NETWORK menu will appear:
SOURCE TYPE :
SRC ISN GNA :
SRC ISN LNA
SRC IDN ID
DESTIN TYPE :
DST ISN GNA :
DST ISN LNA
DST IDN ID
EXIT
Figure 74: MICROS ISN NETWORK Sub-Menu
SOURCE TYPE
Choices: ANY, 00, 01, 02 ,03,..., 09
SRC ISN GNA
Choices: ANY, 00, 01, 02, 03,..., 32
SRC ISN LNA
Choices: ANY, 00, 01, 02, 03,..., 32
SRC IDN ID
Choices: ANY, 00, 01, 02, 03,..., 15
DESTIN TYPE
Choices: ANY, 00, 01, 02, 03,..., 09
DST ISN GNA
Choices: ANY, 00, 01, 02, 03,..., 32
DST ISN LNA
Choices: ANY, 00, 01, 02, 03,..., 32
DST IDN ID
Choices: ANY, 00, 01, 02, 03,..., 15
VSI-Pro Max POS / Cash Register Interface
ANY
ANY
: ANY
: ANY
ANY
ANY
: ANY
: ANY
MICROS 3700 V4.X
Press the "Up" or "Down" button to move the cursor to
"MICROS 3700 V4.X" and press "Set". The sub menu
will appear:
ECR NUMBER
HANDSHAKING
EXIT
Figure 75: MICROS 3700 V4.X Sub-Menu
DISPLAY:
ECR NUMBER 1-9999999, press set to increment to the
next digit, UP or Down to select number and simultaneously
to save the address. Select "HANSHAKING" On or Off.
NCR
Press the "Up" or "Down" button to move the cursor to
"NCR" and press "Set". The NCR sub menu will appear:
NCR 2113, 3110
NCR 7059
NCR 745X [POLE]
NCR JRNL PRINTER
NCR RCPT PRINTER
NCR SLIP PRINTER
NCR7454WS/7197
NCR7456
NCR 5972 [TAP]
- - - - NEXT PAGE
EXIT
Figure 76: NCR Sub-Menu Page 1
- - - - PREVIOUS PAGE
NCR 5972 [ EMULATE]
CRSOSS 7474
REALPOS 30
EXIT
Figure 77: NCR Sub-Menu Page 2
NCR 7059
Press the "Up" or "Down" button to move the cursor to
"NCR 7059" and press "Set". The sub menu will appear:
NCR JRNL PRINTER
NCR RCPT PRINTER
NCR SLIP PRINTER
EXIT
Figure 78: NCR 7059 Sub-Menu
27
5. PROGRAMMING
0000000
ON