Related Manuals for Victron energy Smart BMS CL 12-100
Summary of Contents for Victron energy Smart BMS CL 12-100
- Page 1 ENGLISH Smart BMS CL 12-100 Battery Management System Rev 08 - 11/2022 This manual is also available in HTML5.
-
Page 2: Table Of Contents
3.5.1. Smart BMS settings ....................9 3.5.2. VictronConnect status display ................. 10 4. Specifications ........................11 5. Appendix ..........................12 5.1. Appendix A ......................... 12 5.2. Appendix B ......................... 14 5.3. Appendix C ......................... 15 5.4. Dimensions Smart BMS CL 12-100 ..................16... -
Page 3: Safety Precautions
Smart BMS CL 12-100 1. Safety precautions • Installation must strictly follow the national safety regulations in compliance with the enclosure, installation, creepage, clearance, casualty, markings and segregation requirements of the end-use application. • Installation must be performed by qualified and trained installers only. -
Page 4: Introduction
Smart BMS CL 12-100 2. Introduction 2.1. General description The Smart BMS CL 12-100 is an all-in-one battery management (BMS) system for Victron Lithium Battery 12,8V Smart batteries. It has been specifically designed for 12V systems with a 12V alternator such as in vehicles and boats and supports up to 5 batteries in parallel (BTVs are simply daisy-chained). -
Page 5: What's In The Box
In some cases an interface cable such as a non-inverting or inverting on/off cable may be required, see Appendix A [12]. 2.3. What's in the box • Smart BMS CL 12-100 • Ground wire with 10mm eye terminal • 2-pin plug with pre-installed wire loop • 3-pin plug for load/charge disconnect and pre-alarm •... -
Page 6: Installation And Configuration
Smart BMS CL 12-100 3. Installation and configuration 3.1. Important warning Lithium batteries are expensive and can be damaged due to over discharge or over charge. The shutdown due to low cell voltage by the BMS should always be used as a last resort to be on the safe side at all times. -
Page 7: Controlling A Battery Charger Via Charge Disconnect
Smart BMS CL 12-100 3.2.3. Controlling a battery charger via Charge disconnect • Battery chargers must interrupt the charging process in case of imminent overvoltage or overtemperature of the cells. The Charge disconnect output of the Smart BMS can be used for this purpose. -
Page 8: System Examples
Smart BMS CL 12-100 3.3. System examples Below you will find a selection of system examples. Note that there are many other possibilities. It is mandatory to study Appendix A [12] as there can be different types of cable interfaces within a product group to control chargers, inverters and inverter/chargers from the Load and Charge disconnect outputs of the BMS. - Page 9 Smart BMS CL 12-100 Alarm DC buzzer Relay Remote on/off CHASSIS Alternator AC load Inverting remote on/off cable CHASSIS Fuse Lithium Battery Smart SmartShunt CHASSIS CHASSIS CHASSIS Starter Battery Application example with Phoenix VE.Bus Inverter rated at 3kVA and more This VE.Bus Inverter needs an inverting remote on/off cable to be controlled by the Load disconnect output of the BMS.
-
Page 10: Installation
Smart BMS CL 12-100 3.4. Installation Before installation, make proper system design considerations to avoid unnecessary connections and to keep cable lengths as short as possible. See also the System examples [6] chapter. 1. Preferably mount the Smart BMS on a vertical surface for optimal cooling. -
Page 11: Configuration
Smart BMS CL 12-100 3.5. Configuration 3.5.1. Smart BMS settings The Smart BMS is configured via Bluetooth and the VictronConnect app. See the VictronConnect manual for download and installation details. The following steps describe the configuration process and options: 1. Power up the Smart BMS according to the Installation chapter [8]. -
Page 12: Victronconnect Status Display
Smart BMS CL 12-100 3.5.2. VictronConnect status display Page 10 Installation and configuration... -
Page 13: Specifications
Smart BMS CL 12-100 4. Specifications Smart BMS CL 12-100 Alternator port - max charge current 100A (with a 125A fuse) Input voltage to start charging >13A Current consumption, remote on 16mA (excluding Load output and Charge output current) Current consumption, remote off 5mA (BMS functionality still active) Normally high (Vbat –... -
Page 14: Appendix
Smart BMS CL 12-100 5. Appendix 5.1. Appendix A Loads which can be controlled directly by the Load disconnect output of the Smart BMS: • Inverters: All Phoenix inverters VE.Direct and Phoenix Inverters Smart. Connect the Load disconnect output of the BMS to terminal H of the 2-pole connector of the inverter. - Page 15 BMS to reset the system. The MultiPlus will then switch on and start charging (if connected to an AC power source). • MultiPlus-II and MultiPlus 3kVA or more For more info on how to configure the MultiPlus to work with the Smart BMS CL 12-100 please refer to the document on our website: https://www.victronenergy.com/upload/documents/Manual-Connecting-other-lithium-battery-systems-to-Multis-...
- Page 16 Smart BMS CL 12-100 5.2. Appendix B Error/ Warning Codes E-B30: Calibration failure Internal malfunction – calibration data failure/missing. Contact dealer for support – Fault is not user correctable and Smart BMS requires replacement. E-B31: Configuration failure Internal malfunction - configuration data failure/missing.
- Page 17 Smart BMS CL 12-100 5.3. Appendix C LED indicators (from left to right) 1. Green: Smart BMS is active 2. Blue: blinking – Bluetooth broadcasting, ON – connection established 3. Red: Over-Temperature protection of the Smart BMS 4. Yellow: Charge disconnect output is enabled 5.
-
Page 18: Dimensions Smart Bms Cl 12-100
Smart BMS CL 12-100 5.4. Dimensions Smart BMS CL 12-100 Dimension Drawing Smart BMS CL 12-100 BMS110022000 109.5 6.75 DETAIL SCALE 2 : 1.5 23.3 Dimensions in mm Page 16 Appendix...