Related Manuals for American Audio MIDILOG 10MXR
Summary of Contents for American Audio MIDILOG 10MXR
- Page 1 10MXR User Guide and Reference Manual 6122 S. Eastern Ave. Los Angeles Ca. 90040 www.AmericanAudio.us 11/12...
-
Page 2: Table Of Contents
• Gain, Bass, and Treble for Mic • Balanced XLR Output • High level headphone output • Built-In DSP D-Core™ Sound Card • Turntable ground connectors located on the rear panel American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 2 © ®... -
Page 3: Electrical Precautions
To prevent electromagnetic inter- ference with electrical appliances such as radios and televisions, use shielded cables and connectors for connections. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 3 © ®... - Page 4 INSIDE REFER SERVICE TO YOUR AUTHORIZED the literature accompanying the appliance. to constitute a risk of electric shock to persons. AMERICAN AUDIO SERVICE TECHNICIAN. ® IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS — All the safety and operating...
-
Page 5: Safety Precautions
If prob- operating instructions. There are no user ser- lems occur with the unit, call American Audio ® viceable parts inside. All other servicing should customer support. -
Page 6: Introduction
Caution! There are no user serviceable parts inside this mixer. Do not attempt any repairs yourself, without being instructed to do so by an authorized American Audio service technician. Doing so will void your manufactures warranty. In the unlikely event your mixer may require service, please contact American Audio customer support. -
Page 7: Unpacking
CHANNEL LINE LEVEL SELECTOR SWITCHES - This switch is used to change the selected input from phono to line and vice versa. The switch selectors are on the rear panel. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 7 ©... -
Page 8: Mixer Panel
10MXR CONTROLS AND FUNCTIONS FRONT PANEL American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 8 © ®... - Page 9 CHANNEL VOLUME FADER - These faders are used to control the output signal of any source American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 9 ©...
- Page 10 This function is especially useful when mixing without an monitor. 9. SHIFT (MIDI) - The button has 2 functions a soft and a hard shift. A soft shift is performed by tog- American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 10 ©...
- Page 11 CUE - When the deck is playing, pressing this button will return to the 1st cue point. If the deck is paused, pressing Cue will set a new cue point. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 11 ©...
-
Page 12: Rear Panel
“PHONO” position, and when using line level input devices be sure this switch is in the “LINE” position. Always be sure American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 12 ©... - Page 13 Also be sure your amplifier(s) is(are) tuned off. Remember to avoid damaging pops to the speakers, the mixer is turned on first and turned off last. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 13 ©...
-
Page 14: Front Panel
26. CROSSFADER CURVE ADJUSTMENT - This rotary knob is used to change the way the cross- fader will operate. The crossfader can operate in different modes, “NORMAL CURVE”, “QUICK CURVE” or any variation of the two. (Quick Curve usually used for scratching). American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 14 ©... -
Page 15: Midi Table
00H = released, 7FH = pressed note on 90H (91H) HOT START 2 Right Button / LED 54 /54 00H = released, 7FH = pressed note on 90H (91H) SYNC Right American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 15 © ®... -
Page 16: Typical Mixer Set-Up
This image details a typical DJ Set Up consisting of a microphone, turntables, CD players, and a tape deck. Note: Turntables can only be connected to the PHONO LEVEL RCA JACKS. Be sure the LINE LEVEL SELECTOR SWITCHES are in the "PHONO" position when using turntables. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 16 © ®... - Page 17 10MXR TYPICAL MIXER SET-UP Balanced XLR male to XLR female Cables American Audio V4001™ Speaker Cables Typical Balanced Output Set-up This image details a typical stereo output layout. Note the use of the Balanced XLR Jacks on both the mixer and the amplifier. Always use the balanced output jacks whenever possible. The balanced output jacks should always be used for cable runs in excess of 15 feet.
-
Page 18: Cleaning
CROSS FADER REPLACEMENT The crossfader is “Hot Swapable” which means it may be replaced at any time, even when power is applied. Only replace with American Audio Part Feather Fader Plus. Replacing with any other model fader may seriously damage your mixer. -
Page 19: Troubleshooting
2. Check to see if the connection cables are connected properly. The sound is distorted: 1. Make sure that the Gain level control is not set to high. American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 19 © ®... -
Page 20: Warranty
American Audio concludes, after inspection, affects the reliability of the product; ® if the product has been repaired or serviced by anyone other than the American Audio factory unless ® prior written authorization was issued to purchaser by American Audio ;... -
Page 21: Specifications
-15dB ~ +11dB MID: -13dB ~ +11dB TREBLE: -24dB ~ +12dB Microphone Equalizer: (Maximum Gain, Master Unbal Out) BASS: -15dB ~ +11dB MID: -13dB ~ +11dB TREBLE: -24dB ~ +12dB American Audio - www.americanaudio.us - 10MXR Instruction Manual Page 21 © ®... - Page 22 ©American Audio® World Headquarters: 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-3322 Fax: 323-582-3311 Web: www.AmericanAudio.us E-mail: info@americanaudio.us American DJ Europe Junostraat 2 6468 EW Kerkrade Netherlands service@adjgroup.eu / www.americandj.eu Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99...
Need help?
Do you have a question about the MIDILOG 10MXR and is the answer not in the manual?
Questions and answers