Advertisement
Quick Links
Advertisement
Related Manuals for American Audio Q-MX2 BPM
Summary of Contents for American Audio Q-MX2 BPM
- Page 1 Q-MX2 BPM USER INSTRUCTIONS...
-
Page 2: Main Features
American DJ AUDIO Los Angeles, CA 90058 USA © ® Specifications subject to change without notice. Q-MX2 BPM User Instructions page 2 Start gain by 15dB +/- 2 dB Indicated Master and PFL (Pre Fader Level) Signal Levels Balanced XLR), Booth (RCA) and REC (RCA) -
Page 3: Table Of Contents
(e.g. after transportation), do not switch on the mixer immediately. The arising condensation of water might damage your device. Leave the device switched off until it has reached room temperature. - www.americandj.com - Q-MX2 BPM User Instructions page 3 ® Q-MX2BPM™ mixer. This mixer is a ®... -
Page 4: Functions (Front Panel)
These button also function as a "TRANS EFFECT" A Trans Effect is an effect similar to cutting the output signal with your transformer switches. American DJ Supply © - www.americandj.com - Q-MX2 BPM User Instructions page 4 ®... - Page 5 EQ. These controls are used to increase or decrease the LOW's, MID’s, and HI’s of the output signal. The Q-MX2 features "Rotary Kills" with a -30dB to +20dB gain control. American DJ Supply © - www.americandj.com - Q-MX2 BPM User Instructions page 5 ®...
- Page 6 Channel (1, 2, or 3) assigned to "X" by the Fader Assign Buttons (3). The meter on the "Y" side will display the avaerage BPM's of any Channel (1, 2, or 3) assigned to "Y" by the Fader Assign Buttons (3). American DJ Supply © - www.americandj.com - Q-MX2 BPM User Instructions page 6 ®...
- Page 7 28. GND (GROUND TERMINAL) - Connect each of your turntable ground leads to this terminal. This will reduce the humming and popping noises associated with magnetic phono cartridges. American DJ Supply © - www.americandj.com - Q-MX2 BPM User Instructions page 7 ®...
- Page 8 "AUX 3" position should be connected to AUX LINE input. The red colored RCA jack represents the right channel input and the white represents the left channel input. American DJ Supply © - www.americandj.com - Q-MX2 BPM User Instructions page 8 ®...
-
Page 9: Set-Up
"Phono RCA Jacks (34, 36, and 39) as long as the Line Level Switches (39) are in the "AUX" position. American DJ Supply © Male XLR Pin Confi guration: 1 Ground/Return/ 0v) 3 Negative (- data) 2 Hot (+ data) - www.americandj.com - Q-MX2 BPM User Instructions page 9 ®... - Page 10 Turntables can only be connected to the Phono Line Level RCA Jacks (36, 38, and 41). Be sure the Line Level Switches (39) are in the "PHONO" position. American DJ Supply - www.americandj.com - Q-MX2 BPM User Instructions page 10 © ®...
- Page 11 10 feet. Using the balanced jacks will ensure a clean signal through out the entire audio system. American DJ Supply - www.americandj.com - Q-MX2 BPM User Instructions page 11 © ®...
-
Page 12: Operating Instructions
CROSSFADER REPLACEMENT INSTRUCTIONS The crossfader is "Hot Swappable" which means it may be replaced at any time, even when power is applied. Only replace with American Audio Part Feather Fader Plus. Replacing with any other model fader may seriously damage your unit. -
Page 13: Technical Specifications
+13 ± 1dB, -27 ± 2 dB at 13KHz Warranty & Service: The Q-MX2 BPM has a 2-year limited warranty. Please mail in warranty card as soon as possible to validate your warranty. For any service related issues please contact American DJ customer support at (800) 322-6337, Moday through friday 9:00 am to 5:00 pm Pacific Standard Time, or contact us on the web at support@americandj.com.