EcoSmart AL13-8FT-RGBWW-1-A Use And Care Manual

A - 8ft. Rope Light x 1
Installation
PREPARING TO EXTEND THE
ROPE LIGHTS
Ensure all rope lights are
unplugged before adding the
additional rope light (A) to the series.
Remove the end cap (1) from the last
rope light in the series by turning
counterclockwise.
Remove the power cord (2) from additional
extension rope lights (A).
Extend up to 96ft (29.2 m) maximum. Use only
the following Commercial Electric rope light
extension segments: 1005580337
or 1005580338.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Ground Fault Circuit Interrupter (GFCI) protection should be provided in the circuits
or outlet to be used for outdoor use. Receptacles are available that have built-in GFCI
protection.
Only use outdoor extension cords such as typ SW, SOW, STW, STOW, SJW, SJOW, SJTW,
or SJTOW. This designation is marked on the wire of the extension cord.
The rated voltage for this product is 120VAC, 60Hz, 9.6W, 0.1A.
Do not operate this product with the exible light tightly coiled.
Do not route the cord or exible light cable through walls, doors, windows, or any
similar part of a building structure.
Do not subject exible lighting to continous exing.
Do not exceed the maximum extension length in feet permitted by the marking. The
maximum extension length for this rope light is 96ft. (29,2 m).
The RF remote controller included utilizes a 3V CR2025 battery; only replace with same battery
type. Please dispose of batteries properly. Batteries are not a toy! If swallowed, contact local
emergency services immediatley.
SAVE THESE INSTRUCTIONS
WARNING: This product has a polarized plug (one
blade is wider than the other) as a feature to reduce
the risk of electric shock. This plug will t in a
polarized outlet only one way. If the plug does not t
fully in the outlet, reverse the plug. If it still does not t,
contact a quali ed electrician. Never use with an
extension cord unless the plug can be fully inserted.
Do not alter the plug.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet di erent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modi cations not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
8 ft. LED Color Changing Rope Light
B - Mounting Clip x 4 C - Screw x 8
CONNECTING THE ROPE LIGHTS
Connect the last rope light in the
series and the extension rope.
light (A) together and ensure the
connectors are tightly secured.
Attach the end cap (1) to the last rope
light in the series and ensure the
connection is secure.
Item # 1005580338
Model # AL13-8FT-RGBWW-1-A
Use and Care Guide
D - Handheld Remote Control x 1
MOUNTING THE ROPE LIGHTS
Insert the screw (C) through the
opening in the mounting clip (B).
Screw the mounting clip (B) into
position at the installation location.
Place the rope light (A) securely into
the mounting clip (B).
Mounting clips should be evenly spaced
and be a maximum of 3 ft. (0.91 m) apart.
Make sure the distance between two
lines of rope light is at least 1/2 in. (12 mm).
WARNING: When using this product outdoors,
basic safety precautions should always be followed
to reduce the risk of re, electric shock, and
personal injury.
WARNING: Do not cover this product as the
covering may cause the exible light to overheat
and either melt or ignite.
WARNING: Do not puncture, cut, shorten, or
splice the exible lighting.
WARNING: Do not use if there is any damage to
the light or cord insulation. Inspect periodically.
WARNING: Do not mount or secure the rope
light in a manner than can cut the outer jacket or
damage the cord insulation. Inspect the rope light
carefully before use and discard any rope lights
that have a broken outer jacket, loose connections,
or frayed wire insulation.
WARNING: Do not submerge the exible light in
liquids or use the product in the vicinity of standing
water or other liquids.
WARNING: Secure the rope lights using only the
mounting clips provided. Do not secure this product
with staples, nails, or similar objects that may
damage the insulation.
WARNING: Do not install the rope light within
16 ft. (4.87 m) of pool or spa. Do not install rope
lighting in cabinets, tanks, or enclosures of any kind.
CAUTION:
All units must be unplugged before
you add additional segments. Only use segments
recommended by the manufacturer of this lighting
system.
CAUTION:
Ensure all connections and the end
cap on the last segment are tightly secured to
prevent the entry of water.
Please contact 1-877-527-0313 for further assistance.
E - 3V CR2025 Battery
HOMEDEPOT.COM/ECOSMART