EcoSmart AL-15-13.2-RGB Use And Care Manual

Installation
PREPARING TO EXTEND THE
STRIP LIGHTS
Ensure that all strip lights are unplugged
before adding additional strip light to
the series.
Remove the end cap from the last strip light
in the series by turning counterclockwise.
Remove power cord (B) from additional
strip light.
Extend up to 26.4ft (8.04 m) maximum. Use only
the following Commercial Electric strip light
extension segments:
1005581658
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Ground Fault Circuit Interrupter (GFCI) protection should be provided in the circuits
or outlet to be used for outdoor use. Receptacles are available that have built-in GFCI
protection.
Only use outdoor extension cords such as type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW,
STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW. This designation
is marked on the wire of the extension cord.
The rated voltage for this product is 120VAC, 60Hz, 9.4W, 0.195A.
Do not operate this product with the exible light tightly coiled.
Do not route the cord or exible light cable through walls, doors, windows, or any
similar part of a building structure.
Do not subject exible lighting to continous exing.
Do not exceed the maximum extension length in feet permitted by the marking. The
maximum extension length for this strip light is 26.4ft. (8.04 m).
The RF remote controller included utilizes a 3V CR2025 battery; only replace with same battery
type. Please dispose of batteries properly. Batteries are not a toy! If swallowed, contact local
emergency services immediatley.
SAVE THESE INSTRUCTIONS
WARNING: This product has a polarized plug (one blade is wider than
the other) as a feature to reduce the risk of electric shock. This plug
will t in a polarized outlet only one way. If the plug does not t
fully in the outlet, reverse the plug. If it still does not t, contact a
quali ed electrician. Never use with an extension cord unless the
plug can be fully inserted. Do not alter the plug.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet di erent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modi cations not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
A - 13.2ft. Strip B - 5 ft 120V AC
Light x 1 Power Cord x 1
CONNECTING THE STRIP LIGHTS
Connect the last strip light in the
series and the extension strip
light together; ensure the
connectors are tightly secured.
Attach the end cap to the last strip
light in the series and ensure the
connection is secure.
.
Use and Care Guide
13.2 ft. RGB Pixel Strip Light
C - Mounting Clip x 7 D - Screw x 7
Item # 1005581658
Model # AL-15-13.2-RGB
E - Handheld Remote F - 3V CR2025 Battery
Control x 1
MOUNTING THE STRIP LIGHTS
Place the strip light where it is to be
mounted. Make sure nearby lines
of strip light are at least 1/2 in. apart.
Place the mounting clips (C) over the
strip light. Make sure they are evenly
spaced, no more than 12 in. apart.
Use screws (D) to secure the
mounting clips (C)
Make sure the distance between two
lines of strip light is at least 1/2 in. (12 mm).
C
D
WARNING: When using this product outdoors,
basic safety precautions should always be followed
to reduce the risk of re, electric shock, and
personal injury.
WARNING: Do not cover this product as the
covering may cause the exible light to overheat
and either melt or ignite.
WARNING: Do not puncture, cut, shorten, or
splice the exible lighting.
WARNING: Do not use if there is any damage to
the light or cord insulation. Inspect periodically.
WARNING: Do not mount or secure the strip
light in a manner than can cut the outer jacket or
damage the cord insulation. Inspect the strip light
carefully before use and discard any strip lights
that have a broken outer jacket, loose connections,
or frayed wire insulation.
WARNING: Do not submerge the exible light in
liquids or use the product in the vicinity of standing
water or other liquids.
WARNING: Secure the strip lights using only the
mounting clips provided. Do not secure this product
with staples, nails, or similar objects that may
damage the insulation.
WARNING: Do not install the strip light within
16 ft. (4.87 m) of pool or spa. Do not install strip
lighting in cabinets, tanks, or enclosures of any kind.
CAUTION:
All units must be unplugged before
adding additional segments. Only use segments
recommended by the manufacturer of this lighting
system.
CAUTION:
Ensure all connections and the end
cap on the last segment are tightly secured to
prevent the entry of water.
HOMEDEPOT.COM/ECOSMART
Please contact 1-877-527-0313 for further assistance.