Related Manuals for DK-TEC HNDK
Summary of Contents for DK-TEC HNDK
- Page 1 01/2021 Woodchipper for tractor User manual Original manual Model: HNDK ALWAYS READ INSTRUCTIONS BEFORE USING THE MACHINE DK-TEC A/S - Ærøvej 8, 5800 Nyborg - Phone: 66128222 - E-mail: info@dk-tec.dk...
-
Page 2: Table Of Contents
02/2020 Table of contents 1. Introduction..........................1 2. Safety Labels ..........................2 3. Safety Instructions ........................4 4. Safety equipment........................4 5. Checklist ............................. 5 6. Using the machine ........................6 7. Service and Maintenance......................9 8. Problem Solving ........................11... -
Page 3: Introduction
02/2020 1. Introduction Starting the chipper Always your hand to turn the chipper ejecter toud before starting the machine. Turn the chipper's ejection away from buildings, yourself and other bystanders. Keep the PTO shaft straight and within 15 degrees horizontally when operating the chipper. -
Page 4: Safety Labels
02/2020 2. Safety labels CAUTION: Do not step into or place your body parts in the wood funnel. This can result in serious injuries or death CAUTION: Make sure the drive shaft rotates in the right direction and at the correct RPM Cutting diameter of thickness the tree is mix 12.5 cm... - Page 5 02/2020 CAUTION: Read and understand ALL safety and use instructions in the user manual. Read and understand ALL safety labels that sit on the chipper. The main safety device is a well-informed operator. Noise of 121 decibels Refill lubricating grease. CAUTION: Hydraulic fluid under pressure.
-
Page 6: Safety Instructions
02/2020 3. Safety instructions Do not operate the chipper until you have read and understood the user manual. Be sure that the safetyscreen is installed correctly when the chipper is operated. It is important that the labels are on the chipper and that they are maintained. If your labels have been damaged and are no longer readable,we are happy to live new ones. -
Page 7: Checklist
02/2020 5. Checklist CAUTION: Turn the chipper knife wheel ( Disc ) by hand before connecting it to tractor ensure that moves sig freely, all bolts are tensioned and that the blades do not hit the sides and the knife beam. Make sure that: 1. -
Page 8: Using The Machine
02/2020 6. Using the machine To function properly, the blades must be sharp. Soil, stones, nails and other foreign material shorten the life of the blades. Review the checklist before using the chipper . After checking that there is nothing in the way, you can start the tractor and lift the chipper until the PTO shaft is within about 20 degrees relative to the horizontal. - Page 9 02/2020 Included top bar: • The included top bar is for manually screwing up the top roller, if necessary service and inspection – requires that the tractor and engine have stopped completely! The chipper in the transport position: The photo series here shows how to close up the funnel when transporting. Photo 1: The chipper in working position (pulls the wood in)
- Page 10 02/2020 Adjusting the rolling tension – how hard the roller holds the tree. There is 1 handle on each side. Chipper's knives IMPORTANT: The machine must be completely turned off and stopped before changing the blades! The flywheel and stationary blades must be sharp to get the chipper to do the work as expected. When the blades have become lethargic, they can be turned 180 degrees as a result of which a new knife appears.
-
Page 11: Service And Maintenance
• spare parts are necessary for periodic maintenance and servicing, original spare parts Where must be used. DK-TEC is not responsible for damage caused by unapproved parts and/or accessories. • Have a fire extinguisher and first aid kit easily accessible while performing maintenance on Chipper. - Page 12 02/2020 When What should be done? Daily Lubricate PTO shaft At every 40 hours or weekly 1. Lubricate the telescopic section of the PTO shaft 2. Check the sharpness of the blades: a. Flywheel b. Desktop Remove the blades and replace them as needed At every 100 hours 1.
-
Page 13: Problem Solving
In the following section, we have listed many of the problems, causes and solutions that you may encounter in using the chipper. If you encounter a problem that is difficult to solve even after reading through this section, you can call DK-TEC. Problem... - Page 14 E F - O V E R E N S S T E M M E L S E S E R K L Æ R I N G D K Fabrikant Changzhou Han-Sun Machinery Co., Ltd. 89 Huanbao 4th Road, Huanbao Industrial Park, Hi-Tech, Changzhou, Jiangsu, P.R.
- Page 15 02/2020 Always refer to the latest version of the manual, as well as the spare parts list/parts list for your item on www.dk-tec.dk, under the machine itself.
Need help?
Do you have a question about the HNDK and is the answer not in the manual?
Questions and answers