Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Crystal Vision Dual 3G-DL
Summary of Contents for Crystal Vision Dual 3G-DL
- Page 1 Dual 3G-DL Dual channel single link to dual link converter Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England. E-mail: sales@crystalvision.tv Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059...
-
Page 2: Table Of Contents
Menu tree Status menu Using the front control panel Module selection The Dual 3G-DL active panel menu structure Active control panel menus The Status menu Statesman Statesman operation ... - Page 3 Crystal Vision Dual 3G-DL User Manual R1.0 Trouble shooting Basic fault finding guide Specification Dual 3G-DL User Manual R1.0 24/11/2010...
-
Page 4: Introduction
Introduction 1 Introduction The Dual 3G-DL is a 3G to dual link converter for interfacing between 3Gb/s and 1080p dual link equipment. It takes a single 3Gb/s signal and separates it into two 1.5Gb/s signals which can either be a dual link 3Gb/s signal, or alternatively two separate, co-... -
Page 5: Hardware Installation
Hardware installation 2 Hardware installation The Dual 3G-DL single height module is used with the RM53 rear connectors, which will fit into all Crystal Vision rack frames. All modules can be connected or removed while the frame is powered, without damaging the board. -
Page 6: Rear Modules And Signal I/O
The Indigo DT desk top box has a built-in power supply and will house up to two single height modules. The rear module for the Dual 3G-DL is the RM53. Note: For details of fitting rear connectors please refer to the appropriate frame manual. -
Page 7: Card Edge Operation
LEDs are provided to give indication of power rail monitoring and the switch configuration. 3.1 Card edge controls Dual 3G-DL card front edge view 3.2 Card edge buttons The two tactile push button switches allow the operator to navigate within the menu structure. -
Page 8: Reading Card Edge Leds
Push ENTER to action the change. The display will cease flashing Use the up-arrow [] and SCROLL control to navigate to further menus Notes: The displayed menu brightness will flash slowly if confirmation of a change is required. Dual 3G-DL User Manual R1.0 24/11/2010... -
Page 9: Card Edge Configuration
The electronically stored PCB serial number. This should correspond store serial with the serial number label affixed to the PCB connector. number Notes: If any input is missing all status displays related to that input will show ‘input missing’. Dual 3G-DL User Manual R1.0 24/11/2010... -
Page 10: Using The Front Control Panel
This operational guide assumes that the panel has been set up according to the panel setup procedure described in the Crystal Vision Control Panel manual. It is ESSENTIAL that the panel setup procedure is followed and any old or unknown Note: passwords cleared prior to using the panel for the first time. - Page 11 Crystal Vision Using the front control panel Please refer to the Crystal Vision Control Panel manual for details of the Panel Set up, Lock Panel and Note: Diagnostic menus. Selecting a Dual 3G-DL To select a particular card in a frame, press the DEVICE key to go to the Device menu.
-
Page 12: The Dual 3G-Dl Active Panel Menu Structure
If the variable updates in real time it will be contained within square brackets [Field]. The following chart shows the available Dual 3G-DL menus. The actual menus available may vary slightly as software is updated. -
Page 13: The Status Menu
This should correspond with the serial number label affixed number to the PCB connector. Notes: If any input is missing all status displays related to that input will show ‘input missing’. Dual 3G-DL User Manual R1.0 24/11/2010... -
Page 14: Statesman
Statesman 5 Statesman The Crystal Vision Statesman PC control software is designed to control a range of Crystal Vision modules via serial control from a PC. Statesman provides a user friendly means of configuring and operating Crystal Vision modules with the benefit of “see-at-a- glance”... -
Page 15: Status
The status pane is divided into two sections, one for each input giving information about input present, input format and video level. Further status information is provided by the Statesman logging and alarms feature, which is described in more detail in the Statesman manual. Dual 3G-DL Status menu Dual 3G-DL User Manual R1.0 24/11/2010... - Page 16 Yellow Not currently supported Ch1A Yellow Channel 1 is Level A Ch1B Yellow Channel 1 is Level B Ch2A Yellow Channel 2 is Level A Ch2B Yellow Channel 2 is Level B Dual 3G-DL User Manual R1.0 24/11/2010...
- Page 17 If necessary re-set the card by simply removing it from the rack whilst powered and re-inserting it after a few seconds. It is safe to re-insert the card whilst the rack is powered Check that the remote/local lever is correctly set for the mode of operation Dual 3G-DL User Manual R1.0 24/11/2010...
- Page 18 PSU rails present, inputs present and output routing Control from frame active front panel and remote panel Statesman allows control and status monitoring from any PC on a network SNMP monitoring and control available as a frame option Dual 3G-DL User Manual R1.0 24/11/2010...
Need help?
Do you have a question about the Dual 3G-DL and is the answer not in the manual?
Questions and answers