Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crystal Vision Dual DL-3G
Summary of Contents for Crystal Vision Dual DL-3G
- Page 1 Dual DL-3G Dual channel dual link to single link converter Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England. E-mail: sales@crystalvision.tv Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059...
-
Page 2: Table Of Contents
Status menu Output level menu Using the front control panel Module selection The Dual DL-3G active panel menu structure Active control panel menus The Status menu Output level menu Statesman ... - Page 3 Crystal Vision Dual DL-3G User Manual R1.0 Status Trouble shooting Basic fault finding guide Specification Dual DL-3G User Manual R1.0 26/11/2010...
-
Page 4: Introduction
The Dual DL-3G is designed mainly for use with Level B 3Gb/s signals. Although it will work with Level A signals which do not contain audio or other embedded data. The Dual DL-3G has user controllable selection of level A or B for its outputs and the VPID status of the input video is indicated. -
Page 5: Hardware Installation
Hardware installation 2 Hardware installation The Dual DL-3G single height module is used with the RM50 rear connector, which will fit into all Crystal Vision rack frames. All modules can be connected or removed while the frame is powered, without damaging the board. -
Page 6: Rear Modules And Signal I/O
The Indigo DT desk top box has a built-in power supply and will house up to two single height modules. The rear module for the Dual DL-3G is the RM50 or RM34. Note: For details of fitting rear connectors please refer to the appropriate frame manual. -
Page 7: Card Edge Operation
LEDs are provided to give indication of power rail monitoring and the switch configuration. 3.1 Card edge controls Dual DL-3G card front edge view 3.2 Card edge buttons The two tactile push button switches allow the operator to navigate within the menu structure. -
Page 8: Reading Card Edge Leds
Push ENTER to action the change. The display will cease flashing Use the up-arrow [] and SCROLL control to navigate to further menus Notes: The displayed menu brightness will flash slowly if confirmation of a change is required. Dual DL-3G User Manual R1.0 26/11/2010... -
Page 9: Card Edge Configuration
Card edge operation 3.6 Card edge configuration Menu tree To reach the top menu push the button repeatedly until a top menu is reached. Rotate the Tip: SCROLL control anti-clockwise until the Status menu appears. Dual DL-3G User Manual R1.0 26/11/2010... -
Page 10: Status Menu
The input 2 channel A link identifier is shown. link identifier Link A, Link B. Input 2 Ch B The input 2 channel B video payload identifier is shown. VPID Status VPID, No VPID. Dual DL-3G User Manual R1.0 26/11/2010... -
Page 11: Output Level Menu
Level A, Level B. Notes: The Dual DL-3G is designed mainly for use with Level B 3Gb/s signals. Although it will work with Level A signals which do not contain audio or other embedded data. Dual DL-3G User Manual R1.0... -
Page 12: Using The Front Control Panel
This operational guide assumes that the panel has been set up according to the panel setup procedure described in the Crystal Vision Control Panel manual. It is ESSENTIAL that the panel setup procedure is followed and any old or unknown Note: passwords cleared prior to using the panel for the first time. - Page 13 Crystal Vision Using the front control panel Please refer to the Crystal Vision Control Panel manual for details of the Panel Set up, Lock Panel and Note: Diagnostic menus. Selecting a Dual DL-3G To select a particular card in a frame, press the DEVICE key to go to the Device menu.
-
Page 14: The Dual Dl-3G Active Panel Menu Structure
The variable being adjusted will appear in brackets. If the variable updates in real time it will be contained within square brackets [Field]. The following chart shows the available Dual DL-3G menus. The actual menus available may vary slightly as software is updated. -
Page 15: The Status Menu
50Hz, 59.94Hz, 60Hz, No Valid VPID. Input 1 Ch B Rotate the shaft control to view the input 1 channel B link status. link identifier Link A, Link B, No Valid VPID. Dual DL-3G User Manual R1.0 26/11/2010... -
Page 16: Output Level Menu
Level A, Level B. Output 2 level Rotate the shaft control to view the Output 2 level selection. format Press F2 to select menu. Rotate shaft control to change selection. Level A, Level B. Dual DL-3G User Manual R1.0 26/11/2010... -
Page 17: Statesman
Statesman 5 Statesman The Crystal Vision Statesman PC control software is designed to control a range of Crystal Vision modules via serial control from a PC. Statesman provides a user friendly means of configuring and operating Crystal Vision modules with the benefit of “see-at-a- glance”... - Page 18 VPID status and video output level. Further status information is provided by the Statesman logging and alarms feature, which is described in more detail in the Statesman manual. Dual DL-3G Status menu Dual DL-3G User Manual R1.0 26/11/2010...
- Page 19 Input 2B present Input not present Ch1A Yellow Channel 1 is Level A Ch1B Yellow Channel 1 is Level B Ch2A Yellow Channel 2 is Level A Ch2B Yellow Channel 2 is Level B Dual DL-3G User Manual R1.0 26/11/2010...
- Page 20 If necessary re-set the card by simply removing it from the rack whilst powered and re-inserting it after a few seconds. It is safe to re-insert the card whilst the rack is powered Check that the remote/local lever is correctly set for the mode of operation Dual DL-3G User Manual R1.0 26/11/2010...
- Page 21 PSU rails present, input links present and output level Control from frame active front panel and remote panel Statesman allows control and status monitoring from any PC on a network SNMP monitoring and control available as a frame option Dual DL-3G User Manual R1.0 26/11/2010...
Need help?
Do you have a question about the Dual DL-3G and is the answer not in the manual?
Questions and answers