Advertisement
1
Specifications
Digital DC Inputs
XLE103
12 including 4
Inputs per Module
configurable
HSC inputs
Commons per
Module
Input Voltage
12 VDC / 24 VDC
Range
Absolute Max.
35 VDC Max.
Voltage
Input Impedance
Positive
Input Current
Logic
Upper Threshold
0.8 mA
Lower Threshold
0.3 mA
Max Upper
Threshold
Min Lower
Threshold
OFF to ON
Response
ON to OFF
Response
10 kHz Totalizer/Pulse,Edges
HSC Max.
5 kHz Frequency/Pulse,Width
Switching Rate
2.5 kHz Quadrature
Analog Inputs,
Medium
XLE103
Resolution
Number of
2
Channels
Input Ranges
Safe input voltage
-0.5 V to +12V
range
Input Impedance
Current Mode:
(Clamped @ -0.5
VDC to 12 VDC)
Voltage Mode:
Nominal Resolution
%AI full scale
32,000 counts
Max. Over-Current
All channels converted once
Conversion Speed
per ladder scan
Max. Error at 25°C
4-20 mA
0-20 mA
(excluding zero)
0-10 VDC
Additional error for
temperatures other
than 25°C
160 Hz hash (noise) filter
Filtering
1-128 scan digital running
average filter
Note: Highest usable frequency for PWM output is 65 KHz
__________________________________________________________________________________________________________________________________________________________________
Specifications
Digital DC
XLE104
Outputs
24 including
4
Outputs per
configurable
Module
HSC inputs
Commons per
1
Module
Output Type
Absolute Max.
Voltage
Output
10 kΩ
Protection
Max. Output
Negative Logic
Current per
point
Max. Total
-1.6 mA
Current
Max. Output
-2.1 mA
Supply Voltage
Minimum Output
8 VDC
Supply Voltage
Max. Voltage
3 VDC
Drop at Rated
Current
Max. Inrush
1 ms
Current
Min. Load
1 ms
OFF to ON
Response
ON to OFF
XLE104
Response
2
Output
Characteristics
0 - 10 VDC
0 – 20 mA
4 – 20 mA
100 Ω
Required Power
(Steady State)
500 k Ω
Required Power
10 Bits
(Inrush)
Primary Power
35 mA
Range
Relative Humidity
1.00%
Operating
1.00%
Temperature
0.50%
Terminal Type
TBD
CE
If you require a Compliance Table:
1-888-556-6342
UL
Weight
C
o l
k c
A
c c
XLE103
XLE104
12 including
16 including
2
2
configurable
configurable
PWM
PWM
outputs
outputs
1
Sourcing / 10 K Pull-Down
28 VDC Max.
Short Circuit
0.5 A
4 A Continuous
30 VDC
10 VDC
0.25 VDC
650 mA per channel
None
1 ms
1 ms
Current Sourcing (Pos logic)
General Specifications
130 mA @ 24 VDC
30 A for 1 ms @ 24 VDC
10 – 30 VDC
5 to 95% Non-
condensing
0°C to +50°C
Screw Type,5 mm
Removable
12.5 oz. (354.36 g)
+/- Seven
u
a r
y c
Minutes/Month at 20C
Page 1 of 4
2
Panel Cut-Out and Dimensions
Note: Max. panel thickness: 5 mm.
Note:
The tolerance to meet
NEMA standards is
± 0.005" (0.1 mm).
"
"
3
Ports / Connectors / Cables
Note: The case of the XLe is black, but for clarity, it is shown in a
lighter gray color.
DIP
Memory Slot
Switch
MJ2
(RS-232 / RS-485)
MJ1
(RS-232 / RS-485)
J1
I/O
Jumper
To Remove Back Cover:
Unscrew 4 screws located on
the back of the unit and remove
back cover.
I/O Jumpers (Not Shown): I/O Jumpers (JP) are located
internally. To access, remove back cover of unit.
Wiring Connectors (J1 – J4), I/O Jumpers (JP1-3), and
External Jumpers (RS-485) are described in the Wiring and
Jumpers section of this document.
001ACC009
Power Connector
Power Up:
Connect to Earth Ground.
when using CsCAN network.
Apply 10 – 30 VDC.
Screen lights up.
Torque rating 4.5 - 7 Lb-In
(0.50 – 0.78 N-m)
3.622" [92mm]
001XLE002
"
J2
I/O
Jumper
NET 1
(CsCAN)
Power
001XLE029-R2
CAUTION: Do not over tighten
screws when replacing the back
cover.
CAN Connector
Use the CAN Connector
Torque rating 4.5 – 7 Lb-In
(0.50 – 0.78 N-m)
Advertisement
